Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
I'm using Rigado BMD350 evaluation board. I'm printing to serial port (COM3, speed 112500) using NRF_LOG_INFO.
However, the logging does not appear until debugging is...
In a recent project, me and my team have been trying to send data from 3 PTX devices to a single PRX device (the devices are all nRF24L01+) at a constant rate of 1600Hz from...
hi all!
Like two of my predecessors, I am trying to put a CR95HF into operation. I chose the nRF52832 DK as MCU (SDK 15).
[thread= https://devzone.nordicsemi.com/f/nordic...
I changed only source clock part to internal clock and it doesn't do advertising. When I debug it, it starts to run. When I finish the debug session advertising stops again...
Hi,
I've built a custom board with nRF52832, without other MCU like PCA10040. I use a FT232RL to bridge the USB to nrf UART, flashed nrf5 uart connection firmware ble_connectivity_s132_uart_pca10040...
Hi, I using nrf52810 with custom BLE profile and 4 sec advertising + continuous RTC. Device is battery powered (750 mAh) and PMDC motor equipped. Most of time (90% of day...
Hi,
I am designing my custom board with the nrf52832, which would perform the BLE and I2C functions. I wonder what necessary and basic peripherals it needs, like crystal...
Hi,
I would like to synchronize 2 Sensors with one dongle. So the problem is that we have two sensors and we want to start the measurement at the more or less (1 ms) exact...
Hello,
I am new to BLE as a technology and have a question regarding how Peer Manager handles bonding.
As I currently understand, the function of bonding is to enable...
Hi,
I want to use nRF52832(PCA10040 board) to communicate with nRF24L01+. I program the example application( \examples\proprietary_rf\esb_ptx)(SDK v15.0.0) on the board...
Hello. I'm developing an application with a custom bootloader and I'm using "settings" data structure placed in FLASH. Because we can erase only full pages, the first page...
Hi.
I want to implement multirole on the nRF52832. I want to advertise beacon data while scanning. So, I modified ble_app_uart_c in the ble_central example. Below is a description...
Hi,
I try to program hex file with openOCD. The flash part is written without any problem. OpenOcd only fail to write the UICR registers beyond 0x10001200.
However it...
Hello,
Which one of the following statements regarding " sd_ble_gap_connect " function call is true:
(1) Can sd_ble_gap_connect function put the central device into initiating...
