Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
I'm using the nrf52832-QFAB variant (32K RAM 256K Flash)
The part is marked as NRF52832 QFABB0 1630AC
Surprisingly, this part is happily running my application and bootloader...
Hello,
I can't find where in flash the peer manager data is stored. I'm currently working on DFU support and as part of that I want to define the memory area that should...
As per mesh_hw_resources.md (MESH_SDK/doc/introduction)
## Flash lifetime The flash hardware can withstand a limited number of write/erase cycles. As the mesh stack uses...
Hi all,
I am trying to develop the BLE Heart Rate Collector example on the nrF51 Development Kit. As far as I read in the Nordic web ( http://infocenter.nordicsemi.com/index...
I'm trying develop on a custom board based on the nRF52832 and am running into some issues. When I run the blinky application (with no SD) the application executes fine. However...
Hi I'm developing beacon firmware using ble_app_beacon example code.
I was able to send good beacon data for my purpose. For the next step, I want to turn on the LED which...
Hi,
I am using a custom board based on nRF52 (nRF52832-QFAB-R) and programing it with softdevice.hex and "ble_hid_mouse" example application in the nRF5 SDK v14.2.0. the...
Hi,
I am using softdevice S132 V2.0 for nrf52832 controller.I am using BLE UART app. It is working fine on eval board.But when i checked it on custom board developed by...
Hello,
I am using sdk12.2.2 and nrf52. I have implemented fds_read, fds_write, fds_delete and its working as expected. Now when I am trying to use fds_update my data is...
We are trying \Nordic\nRF5_SDK_12.1.0_0d23e2a\examples\ble_peripheral\ble_app_uart\pca10028\s130\arm5_no_packs
I want to control UART. If device is not in use i want to...
I'm just starting to bring up a custom board based on the nRF52832 and I am unable to program it using the J-link. It looks like my reset line gets stuck low when the JTAG...
Hi,
I work on the PCA10028 devkit with the nRF5_SDK v 12.3.0.
My project implements the ESB comunication concurently with the BLE by using the timeslot API.
I can send...
Dear Sir,
at the past I already ask this question at old forum, but now I can't find this ticket so I ask it secondary.
If I use a circuit configuration no.5 but USB is...
