Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Hello Nordic,
I have seen a couple of your reports and I am not sure how to read the inband image frequency. You have put frequencies in there (I thought values should be...
Hi
What is exact difference between following versions of nrf51822QFAC chip 1.nRF51822-QFAC-T 2.nRF51822-QFAC-R7 3.nRF51822-QFAC-R
I am searching for nrf51822-QFACAx chip...
Hello
I am trying to move an arduino project where I read an ADC value from a FSR sensor. In arduino the FSR is powered by 5V and has 10Kohm pulldown resistor. The board...
hi,everybody
I want to design a sniffer for 2.4G raw data，I have some problem below
1.How can I set the radio register to recieve all message on same frequency；
2.I...
I want to create a PCB circuit withe the nRF52810 Transceiver. If you do not understand what i have in mind:
http://si.farnell.com/nordic-semiconductor/nrf52810-qcaa-r7...
We are seeing a potential issue with a product. on start up a pin is read and the read value determines if we go in to a test mode. Pretty standard.
Our failure is during...
Hello
i just bought my DK-nrf52 to move to BLE after playing few months with arduino. I have connected various nrf52832 shields from China (from Holyiot 17095, which is...
Hello, I want to test Round trip delay using BLE MESH 2.0.1 Light Switch Example Code...I have modify simple on off Light Switch Example. Example test using two Development...
Scenario:
We have three verticals in our project. The nrf51822 based device, base station (BS) and server running on cloud.
Problem Statement:
I need to continuously...
I have downloaded "nrf5_SDK_for_Mesh_v2.0.0" yestoday, and try to setup the "light_switch" demo with 3 pic nRF52 DK.
According to the document description, “proxy_server...
Hello,
I have a query regarding the implementation of multiple user-specific GATT profiles in our application.
For example, can we add two profiles like Heart Rate Profile...
I am migrating from SDK v14.2.0 to v15.0.0 and from S132 to S112 (v6) using the NRF52810. I have mostly everything migrated, but a functionality that worked before does not...
Hi,
I'm trying to use the extended advertising to advertise more than 31 B per packet.
I have been through posts on this forum and the ble_app_rscs example to figure out...
