Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Dear Staff,
we have some Ublox C2909 TAG based on your nRF52833 chip.We need to program them for an RTLS project.
In particular we need to:
customize the FW here ...
Hello,
I managed to run the examples for nrf54l15 channel_sounding_ras_initiator.c and reflector on my custom hardware boards. I changed the overlay files to use my own...
Dear Nordic guy,I'm developing with nrf51822 (6.0 stack binary and 5.0 SDK).
I recently updated the code and stack binary(6.0 stack binary and 5.0 SDK).
My function is not...
static conn_mw_handler_t conn_mw_handler_get (uint8_t opcode)
Inside the function,
for (i = 0; i <conn_mw_item_len; i ++)
{
if (opcode == conn_mw_item [i] .opcode...
It seems like it should be easy, but I've spent a fair amount of time and haven't found a way. I only see options 5.0.0 and 5.1.0. There are also links to earlier SDK versions...
Hello All,
Sometimes is fine to use a forum but sometimes we have to meet a deadline and the forum questions don't always get answers for in a timely manner.
So I'm...
I would like to use Channel 0 of the S310 Stack V1.0.0 on the nRF51422 to do a background scan of ANT devices.
I am testing against ANTWARE II v4.1 with the ANT+ usb dongle...
Hi,
I'm working on the ble devices to transmit sensor data using s110 and s120 with one connection.
I want to send 6 packets for every 7.5 ms connection interval from the...
I have been to a number of Nordic events this summer, and it was hinted / suggested / unofficially announced that there would be a third SKU of the nRF51822, that included...
Hello,
I am creating a PCB design for NRF2402AG but I'm not sure whether I should connect pad under the NRF to the ground or I should left them isolated. I could not found...
Hello
I get this error when I try to program the module:
Parsing hex file(s).
ERROR: Cannot find C:\Nordic Semiconductor\nRF51 SDK_v6.0.0.43681\Nordic\nrf51822\Board...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
Hi dear friends from Nordic Semi,
I´m in great trouble trying to make these nRF24L01+ to work, one unit as a transmiter, and one unit as a receiver, it can be to send 3 bytes...
Hi,
I am using nRF51822 Evaluation Kit along with keil uvision4. Will using optimization in keil IDE make any problem in the normal working of BLE project? Will it affect...
Hello All,
We need to design a Remote Control based on NRF24LE1 working with mercury cell.
So they key factor is hardware & software optimisation for the lowest possible...
Is anyone aware of any of these on the market yet? I know of one, from Insight SIP, but am keen to hear about any others.
(This would save space on the PCB, simplify our...
Using twi_sw_master have discovered that the nrf51422 E00 draws 1.3mA in off mode.
When the twi device is removed from the bus, the nrf51422 draws under 5uA in off mode...
