I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
Hello,
I'm designing an application where both, BLE and Ant should / could be used. I tried to download the S310 SOFTDEVICE from www.nordicsemi.com/.../nRF51422 . I'm asked...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
I need a low latency stereo digital streaming device and the model (nRF24Z1) is going to be discontinued.
Has Nordic a replacement for nRF24Z1?
PD: i need stereo, so...
In our product we have both a DFU profile and an application profile which is confusing Mac OS X 10.9 "Mavericks" since it caches device services unless it receives a service...
Hello,
I'm a new developer on nRF51822 and I'm trying to make a program that allows the nRF module to communicate with a glucose meter and a Smartphone application. My...
I'm working with the nrf51-app-ble-lbs demo from github. I notice that when I'm using BLE scanning apps, the VS service UUID is long (128 bits), whereas if I'm looking at...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hi
I am new to embedded programming and I noticed that nrf51822 is a good and complete choice to start with both wireless and 32 bit arm programming.
However, I am not sure...
Hi,
We are trying to add gatt characteristic, we have a reference code which is BLE based,
but other chipset and we are trying to port the code to Nordic 51822 chipset using...
hi,
is it only possible to go with the single profile on the client side like hrs experimental example, or we can implement a central which can connect upto 8 devices,...
Are there any nordic ICs that only have transmit capabilities? Would there be any power benefit to only supporting transmission if the application only needs to transmit ...
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Dear All,
I just got my new nRF51822-mKit. And try complie mbed sample app and deploy to the mKit. It work fine.
But when i try nRF51 SDK sample with Keil 5, eg.:
...
