It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
Background
For reasons that I do not want to dispute here, I am building a custom bootloader for the APP + NET cores on the nRF5340. This custom bootloader is not a Zephyr...
I am testing out the nRF54H20 on the nRF54H20-DK version 0.9.1. I have followed the steps for setup in the "Getting started with the nRF54H20 DK". I currently have nrf54h20_soc_binaries_v0...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I'm trying to run the DFU sample l9_e5_sol on a custom board using the nRF5340 and SDK version 3.0.2.
My goal is to perform DFU over BLE using external flash. However, before...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
Hi, I am developing a BLE application using SPI and TWI. (Using nRF51822)
This discussion is about my survey in development zone for future develop the TWI part.
I want...
I'm calling ble_bondmngr_bonded_centrals_store in response to BLE_GAP_EVT_DISCONNECTED as is the case in plenty of sample code, but when ble_bondmngr_bonded_centrals_store...
Hi Guys,
I have managed to get the BLE DFU demo service working fine (dual bank) on nRF51822 EK. I use a Linux Python program ( bitbucket.org/.../nrf51_dfu_linux) (with...
what is the detection speed, when the beacon
enters into a wall unit area? With their 868 beacon they can
detect in 0,2 seconds. Is the nRF51x22 in sleep mode and does it...
For our application, As I used 24LU1(host) with 51822(device) be the platform.
I hope to transmit Audio data with 8 kHz, 10 bits data format. To commit the requirements ...
Hi,
I have installed "mastercontrolpanel.3.4.0.8098.x86.msi" on my PC, I could not find my master dongle after runing it with my dongle be inserted in USB slot. The screen...
Hello all,
I am getting an error when my device disconnects from the client. The error occurs while bond storage due to data limit exceeds.
err_code = ble_bondmngr_bonded_centrals_store...
Hi all,
I have made some modifications to the bootloader example project (dfu_dual_bank_ble, s110) to get a bootloader that meets my requirements. It is working ok, I can...
I debugging some function abnormal after OTA problem, and problem with disappear after redo OTA FW upgrade, duirng it I found a problem about Master Control Panel FW upgrade...
From the datasheet, the On mode with all blocks idle draws 2.6 uA.
In my code for the PCA10001, I immediately set:
void sleep(void)
{
__SEV();
__WFE();
__WFE();...
I was going through online material all of which mention that the profiles and protocols (GAP,GATT,L2CAP) i.e. the host for a BLE implementation is a software stack rather...
Hello - I have gotten blinky_example up and running in eclipse using the SDK 5.2, nan-29, and some additional google-fu.
Now when I press debug and the play button, it...
I am trying to use nRF UART app and nRF8001 chip. But I cannot change the device name. I intend to change the device name after nRF UART app detects the device. Plus when...
I'm trying to create a method so a users can initiate an OTA update from a paired device. To that end I've written something which is supposed to invalidate the data at the...