I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
Was anybody able to connect to HTS (Health Thermometer Service) on iOS applications, OTHER than nRFToolbox or LightBlue? Which applications did you use?
I tried a dozen...
Greetings....
It is great that you provided SDK UART coexistence example for nRF5 SDK for Mesh v3.1.0 and nRF5 SDK v15.2.0 release for Client node with nRF52832 DK. However...
I am trying to build an example code for PCA10040, but I always have a lot of compiler error: C:/Program Files (x86)/SEGGER/SEGGER Embedded Studio for RISC-V 4.42/source/thumb_crt0...
Hello,
I'm working with the Nrf52832 Dev Kit and the ble_uart_example. After flashing with the hex file and powering the Dev Kit, the on-board-LED starts to blink. Now I...
Hi Nordic team,
I am currently developing a concurrent wireless application with BLE and a proprietary protocol using the timeslot API.
My setup:
nRf52840 DK
SDK...
Hello, guys!
We are working with SDK 15.0.0 and nRF52840 SoCs.
There is a need to transfer a few MBytes of data from the PC to nRF52840 and then on external flash memory...
Hi
this is the code I'm trying with my buzzer,
I want it to generate sound but with different frequencies.
".base_clock = NRF_PWM_CLK_1MHz," I can only as low as 125kHz...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). I am trying to combine the examples ble_app_uart...
Hello.
I am trying to run the throughput example for the Connect SDK, using a 52840 DK and a 52833 DK.
https://github.com/NordicPlayground/fw-nrfconnect-nrf/tree/master...
With sdk16 cli, each command displays help message when used with -h option. It would be nice to have a help command which can display all active commands and their help ...
Hi,
I would like to use raytac MDBT50Q-U without an 32 mhz external crystal.
Periphal examples like "blinky" work but ble does not? nrf_sdh_enable_request fails with invalid...
Hello,
I am using SDK SDK_15.3.0_59ac345 with soft device in application that controls a GPS IC from UART (AT command), also the application is running in background beacon...
I refer the following the link . https://devzone.nordicsemi.com/f/nordic-q-a/33606/updating-advertising-data-manuf-spec-data-in-sdk15
I understand the adv data update. I...
Dear Sirs,
I would like to use in my program computed heart rate as a parameter.
Could you please give example how can I get to this value? I just found in page_0 such...
Hello,
I'm trying using \examples\ble_peripheral\ble_app_uart on PCA10040
I'm programmed s132_nrf52_6.1.1_softdevice, using nRF5_SDK_15.3.0_59ac345 with pca10040_s112_nrf52832_xxaa...
