This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
For some reason, it seems that I am not able to send any raw data with the BLE radio. I am able to configure the radio and start it successfully. However, the radio never...
Hi,I used Nrf52832 connect BMX055 with i2c, I use sdk nRF52_SDK_11.0.0 example examples\ble_peripheral\ble_app_cscs and add my code to read the BMX055,but when it work a short...
Hi Nordic,
i have a question regarding the emBuild.exe tool and the optimization level it will use during building a hex file. I'am using the following command combination...
Hello,
How can I determine the current consumption of Bluetooth 5 use nrf52832 soc with transmission at -4 dm when in the datasheet mentioned only the current consumption...
Hi,
I've just got an Arduino Nano 33 BLE with the NRF52480 chip on it.
I've been trying to manage the Pin configuration by setting the register values through the Arduino...
Hi,
I am using a NRF58240-dk pca10056 S140.
I have an external SD card device connected which, I am writing live sensor data to then advertising that data over a ble advertisement...
Hi ,
The device required to keep advertising during the connection established.
It is human interface device which mean it is peripheral device as well.
I would like...
Hello there,
A while ago I started developing on the nRF9160DK but I found an issue that I do not know how to solve by myself.
I used two SIM cards: the one from iBasis...
._build\nrf52832_xxaa_s132.axf: error: L6002U: Could not open file ..........\external\micro-ecc\nrf52_keil\armgcc\micro_ecc_lib_nrf52.lib: No such file or directory
Hi all,
Is there any sample sdk example for transferring audio file from nRF52840 to my mobile? Is it possible to transfer audio file through Nordic Uart Service? Thanks...
Hi,
I am developing a product based on nrf52840 soc, I need to write a softdevice, program hex file, bootloader on the chip. when I want to select them all in the nrf...
I am trying to set up the LPS22HB sensor with an nRF52840. I am starting with the twi_sensor example(SDK16->examples->peripherals->twi_sensor) and adding the lps22hb example...
We have added custom HID firmware and are able to discover it on the Android Bluetooth Settings app. iOS fails to show the Bluetooth device on iOS Bluetooth Settings app....
Hi,
My task is..
Device will advertise for 20 seconds if there is no connection then it will go to sleep mode for 40 seconds. After 40 seconds it will wake up from sleep...
I have the nRF9160DK 0.8.3 which appears to align with the suggested schematic in "Objective Product Specification v0.7.1" I downloaded the hardware files form the Getting...
