Hi,
We have a device using nRF Connect SDK v3.0.2.
The issue is when we try to do FOTA download and we disconnect the WiFi network (power down the router AP) while it...
# nRF54L15 PDM clock runs at ~1/32 of expected (PCLK1M instead of PCLK32M) on a custom board -works on DK
## Summary
On a custom nRF54L15 board, the PDM peripheral...
Hi,
I am using nRF54L15-DK board for development and currently I am trying to talk to an external module via SPI (nRF dev board is the master). I have disabled the external...
I am trying to setup SPI00 as SPI slave on nrf54l15 but not work as expected.
My board configure is like
and c program like
The program intends to use nrf54L15...
We have two organizations/projects in our nRF Cloud account:
Jackwoida 51789c46 Team (retain)
James_Eval (remove)
I am the account owner/administrator. The James_Eval...
i'm writing bare-metal code for the FLPR (which was loaded by a bare-metal launcher running on the M33)....
when my FLPR code "idles" using the WFI instruction, power consumptions...
I want to use the Softdevice Controller without a crystal on the RTC. I configured my project with
Advertiements look fine, but interaction with a BLE central either throw...
Hello All,
We need the following for reference purpose only
nRF6939-HW
nRFready Smart Remote 3 for nRF52 Series Hardware Files
www.nordicsemi.com/.../nRFready...
Hi,
I am building a custom PCB using the nRF51422 chip. I need to include a pushbutton switch on the PCB to generate an interrupt when it is pressed(gpiote). I am connecting...
Hi support team,
I'm using Nordic nRF52840 with PCA10056 and SDK 14.1. I have a problem with UART connection.
I have a custom board which need to hook up UART connection...
Hi! I am currently doing my project on BLE beacons. I am using nordic's nrf51822 and waveshare ble400.
I am using a blackmagic probe instead of jlink to program it using...
Hello,
my sdk is from nRF5_SDK_12.3.0_d7731ad, I added the dfu service to the ble_app_uart project on nrf51822QFAC,but it just could run to serviive_init() function and...
I am using a bootloader based on the secure serial DFU bootloader example in SDK 13 and tested it on a development kit. I noticed that hardware flow control is enabled in...
nRF52810
1,
Conditions: Two dma buffers are used, SHORT = TASK_STARTRX, 1M baud rate (10us / B)
Phenomenon: At END_RX interrupt, I called GPIO0 = low. With the logic...
Bluetooth Mesh Glossary of Terms mentions 3 different kinds of addresses: Unicast Addresses , Group Addresses and Virtual Addresses .
I think I understand what a Unicast...
I'm developing firmware for the nRF52832 in eclipse, and since I'm using the NFC pins as GPIOs I need to include the "CONFIG_NFCT_PINS_AS_GPIOS" cflag in my Makefile. However...
I've noticed that if I have data queued to go out over the uart (using app_uart_fifo) if I do an fds_record_update the UART TX is effected. You can see what's happening in...
I have put my code developed on a nRF52 dk on a custom board that is based on a ISP1507 CPU. We are having higher current consumption than expected, I use the exact same code...
Hi There,
In company we are working with nRF8001 (currently C revision) and we want to send some custom data in an advertising packet. However, when C revision is selected...
From the S132 5.1.0 specification, I expect that its RAM usage should be only 0x1228 bytes plus ATTR_TAB_SIZE. However, when I compile two of the example projects using IAR...
I am working on a project in Nordic SDK 8.1 that requires using a timer. I am confused where I need to define the timer though (using APP_TIMER_DEF). If I put it right after...
