Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
I'm running into a weird timing issue with a nRF24L01+ which I'm not quite sure how to work around in the general case. The basic setup is two radios, A and B. Auto acknowledgement...
I am using mbed library to get leg up on development.
This is the first time I am writing any MCU application and it sure makes things a lot easier.
I am using nRF51822...
I'm ending up in the HardFault_Handler() on calling sd_app_evt_wait() within a function that reads from the UART. What might cause that? Stack screenshot attached.
I have...
I'm using nRF51822 for development. and I want to use ADC to measure the electricity of battery, but I don't know the discharge characteristic, i couldn't get that on internet...
#define IO_CHERRY8x16_ROW_PORT 0x13E02040UL
#define IO_CHERRY8x16_COLUMN_PORT 0x60031FBFUL
Why this number be defined like this ? What are this two things use for?
...
Hi,
I'm trying to compile the bootloader example using GCC instead of Keil compiler.
To do so, I copied the bootloader example and started editing the file bootloader_util_arm...
Hi, I am working on my new project. My goal is a sensor network. I have to create four service, one or two basic service like htm and battery service and other with contains...
Referring to the PCA10001 schematic, there is a solder bridge SB1, which connects AVDD with VCC_nRF.
Can you please explain in which cases is it needed?
Thank you
...
Hi all,
I test the DFU as follow:
erase chip, program "s110_nrf51822_5.2.1_softdevice.hex"
program "bootloader" by using nrfjprog.exe
"DfuTarg" can be found...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
I'm trying to build the bootloader for gcc/Eclipse.
I used the manual setup approach described here.
However, I can not fit in the allocated space, because...
SDK version: 5.1.0
S110 version: 6.0.0
chip: nRF51822
I am experimenting a generic Data transfer hid device, the report map is as follows:
0x05, 0x0C, // Usage...
Hello Nordic team,
I am working on a BLE RedBearLab shield (nrf8001) mounted on an Arduino board.
Consider that a connection is correctly made from a Master app to my...
I've been running various code on a 51822 that has used PPI, timers, events, GPIO pin config and so on. Supposing I've lost track of what state the retained registers on the...
Hi,
I am new to ANT programming, and was following the userguide's steps to set up my nRF51422 evaluation kit (pca10003 board). I can compile and upload the blinky example...
Hello Guys,
I am having a hard time figuring how to add the nRF51xxx algorithm into Keil. According to nRF81522 Evaluation Kit user guide this should have been installed...
