Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
Hi,
I got a question on power consumption:
In my case, I do not need RF functions on most of time. If disable RF function, what working current of nRF51822 would be? ...
when phone connect to the device, I print the connected address.
However, I find that the bluetooth address is not same with the phone bluetooth address.
here is the debug...
Hi,
I am trying to include temperature (read from DS18B20) in advertisement data using BLE_UUID_HEALTH_THERMOMETER_SERVICE. So far it works fine, but my temperature is...
Hey,
I am using twi_hw_master.c and twi_master.h libraries for twi and want to disable i2c to save power when not in use.
I use the following two lines to disable the i2c...
Hi,
i am using Eclipse 'Mars' and Segger V5.10c to debug some of the SDK examples. The Eclipse command line shows only binary garbage. How can I get the garbage readable...
Hi,I am using s130 softdevice and SDK9.0 .I add static passkey(123456)in my project base on ble_app_uart project and basic functions have been achieved.But I have a question...
Hello!
Is it fine to ready NRF_RADIO->FREQUENCY right after receipt of BLE_GAP_EVT_ADV_REPORT?
Does its value have a relationship with recent adv. report?
hello there when i am trying to open project C:\nRF51_SDK_8.1.0_b6ed55f\examples\ble_peripheral\ble_app_template - Copy\pca10028\s110\arm4. i am getting error like
Third...
Hi,
I have set connection interval as 1.8s.
But i have transmit data every 1 min.
I noticed that BLE transmits data every 1.8sec.
Can someone please tell me what is...
I have just exported a project from mbed, to the Keil uVision4 tool chain.
Create New Project "BLE_Thermometer" on mbed.
"BLE example for the Health-Thermometer...
I see in the information about the nRF51 talking about the support of 4.2. But it is not clear to me the extend of it. I am focus on the link layer and I would like to know...
Is it possible to implement 2 peripheral in one device (need to connect a peripheral device with two different centrals)? When should i expect for this feature?
I have a question about how much memory is required for app timers.
The comments for APP_TIMER_BUF_SIZE state that the buffer size must be one more than actually needed...
