Hello,
I am currently evaluating MCELL location on an existing project, based on nRF9160.
After some trial and errors, I managed to get it working.
However, I ma a bit...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
Hi,
We are developing an application that requires synchronization between two or more nRF9160-based devices. We have the following requirements and constraints:
Required...
I'm using the prebuilt Aliro stack (libaliro.a, nRF52840), when a session fails inside the library we have no way to get the resulting AliroErrorCode. The stack entry points...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
Hi,
I use nRF51422 in Dual mode(SD310) with SDK10 Version.
The profile is CSCS.
I want to ask
How to just show Speed Sensor or Cadence Sensor.
Here is what I did just...
Hello,
I'm evaluating the feasibility of using the nRF52832 chip on a board with a microprocessor running Android and I like to know if Nordic has released or is planning...
I'm using SDK nRF5_SDK_13.0.0_04a0bfd and compiling the example ble_peripheral/ble_app_hrs/pca10056/s140/armgcc using Eclipse Mars 2.
Flashing softdevice s140_nrf52840_5...
Dear Nordic.
I cant found stack API documentation for study.
All company give it for user, for example TI.
User open doc folder and can reed API.pdf file.
Where your...
I use NRF51822_xxaa, sdk12.2, arm_gcc 4.9_2015q3
when i flash hex file experimental_ble_app_blinky_pca10028_s130.hex from C:\NRF\SDK_12.2.0\examples\ble_peripheral\experimental_ble_app_blinky...
Hi,
i have NRF51822 beacon(PCA20006) and NRF51dk KIT(PCA10028).
I am connect a touch sensor and it's gives output in form of "HIGH & LOW".
and i am able to detect the output...
hi,
i want to connect sensor to nrf51822 to send data to smart app continuously over ble.i want to modify example ble_app_beacon. which functions i need to change?
Hi all,
I have implemented a service with various "long char" characteristics. The buffer that I use to receive the data wrote to the "long char" characteristics is this...
I use SDK 9 and nrF51 in the advertising mode. I want to advertise each 1s packets.
First, I call function
set_adv_params(&m_adv_params);
where I
static void set_adv_params...
Hello,
I try to implement the BLE / Cycling Speed and Cadence Service and try to figure out, how to initialize the ble_cscs_init_t data structure. Currently I'm wonder how...
I am building a cadence sensor form the Cycling Speed and Cadence Service module.
Unfortunately the sensor I have built is recognized to have both speed and cadence when...
hi
i flashed s110 softdevice 7.1.0 then ble_app_beacon example application fron sdk 7.1.0 into nrf51822 beacon successfully.but led is not at all blinking in beacon.and i...
Hi
I have got two nRF52840-pdk for long range application design. After reading posts here I realized that the softdevice s140 can only change PHY to CODED after a connection...
Hii guys I am using an nrf51 DK board for my project and I am trying to find the number of advertisements send from the time the board was power up or reset. From my knowledge...
