Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hi,
I'm currently evaluating the use of the nrf52832 as an HCI interface with a linux host and realized from the various questions that the nrf SDK does not support the...
I am running on Uvision. 5.23.
I am running a Central on one PCA10040 DK and a Peripheral on a second PAC10040 DK.
When I run a first RTT Viewer V6.22 (with SWD Target...
Below is from SDK14.2.0 ble_gap.h
There is no white list variable.
/**@brief GAP scanning parameters. */ typedef struct { uint8_t active : 1; /**< If 1, perform...
I am developing a general case application for several devices I am developing. The application template will then be modified in small ways to support different hardware...
Hello everybody, I try to send nus_string data. I bought different inputs and outputs like this;
INPUT;
OUTPUT;
"aaaaa" received // Send 5 times "a"
INPUT;...
Hi team,
I looking for an example on how I can setup a mesh to send and receive string of characters from and to mesh nodes.
I have couple of nrf52832 modules connected...
hello there i downloaded nordic's new mesh sdk. i am using nrf51dk. in mesh sdk there is no keil project . only source file is given. can you tell me how to make project using...
Dear Nordic-Support,
my questions are in regard to the nRF52840 PDK and the SPIM-frequency rates.
The Objective Product specification lists possible configuration...
I would like to use an nRF52840 as a sniffer between my phone and an other nRF52840. I tried to follow the nRF Sniffer guide 2.1 but the firmware seems not working as LED1...
Hi everyone,
I am trying to advertise data from nrf52832 to a smartphone (nRF Connect).
Below are my advertising parameters.
ble_adv_modes_config_t options = {0};...
Hi,
What is the max timer frequency that the nrf52840 can handle in counter mode?
I see that the timer runs at max 16Mhz when in timer mode, is it possible to get 32Mhz...
Ok I’m new to ARM / Nordic and Bluetooth but after a bunch of reading I downloaded SES and the Mesh SDK and got the light switch demo to both compile and run on a few boards...
