Good day,
I've developed a board with a MDBT50Q on it. I'm using the Reg0 DC/DC and LDO Mode Disabled reference circuit ( https://www.raytac.com/download/index.php?index_id...
Hi,
I have the issue that my Zigbee device reports the error "Production configuration is not present or invalid (status: -1)". I followed the guide from this( https://docs...
Hi,
I am using an nRF52840 as a Zigbee NCP. I have built the firmware myself using nRF Connect, and I am also running MCUBoot. Sometimes after some usage, the chip starts...
Hello everyone,
I am testing out I2C on the nRF54L15 for a custom PCB project.
I first tested a simple mpu6050 sensor on &i2c21 on pins P1.11 for SCL and P1.12 for SDA...
I have a bit of an unusual use case where the nPM1300 is quite ideal but need to use an external charger for the battery instead of the internal charger. The nPM1300 fuel...
Hello,
We are currently developing with the nRF9151 and would like to request more information regarding GNSS SNR testing.
We have reviewed the documented GNSS functionality...
Hello,
Is the nrf54 family's I2C peripheral compatible with I3C? I need to communicate with several I3C sensors on the same bus.
If yes, is the software support only...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Dear nodic engineer:
i want test environment temperature with NRF51822 inner temperature module.
any information for reference?
any temp graph?
if need calibration?...
Hi,
I have an evaluation kit and I have custom boards that has nRF51822 chip on them.
I am trying to update the firmware(Application) of the custom boards from evaluation...
Hi,
I need to drive a piezo buzzer. Just need to make a simple beep function(s) that one call will start generating a specified frequency on specified pin and other call...
there is no sample code in nrf5188 sdk to use BLE_GAP_CONN_SEC_MODE_SET_SIGNED_NO_MITM,
what's the difference between the two settings?
for BLE_GAP_CONN_SEC_MODE_SET_SIGNED_NO_MITM...
Hi,
I am using IAR Workbench for ARM to develop my application and I'm experiencing a very frustrating issue with my debugger (J-Link that came with the development kit)...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hi,
it happened that we have some hardware boards populated with older chips rev. QFAACA and some with newer rev. QFAAG0 but we need to share same software. As I read newer...
by set a char with BLE_GAP_CONN_SEC_MODE_SET_NO_ACCESS, means it can't be read and write, if so, why not remove the char?
any reason behind BLE_GAP_CONN_SEC_MODE_SET_NO_ACCESS...
Is there anyway to limit the number of channels a device is advertising on?
I'm using an nrf51822 with the S110 stack and want to limit my device to a single advertising...
Hi,
We want a throughput between a BLE link 12KBytes/s.
In our application there is a peripheral (in Nordic starter kit), running S110 and we have configured connection...
I have two questions.
Is it possible to use the DAP[n]/DAB[n] registers without using Bluetooth 4.0?
If it is possible, then how? I searched all the sample...
