I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
My computer is running KEIL MDK4 and nRF51 SDK4.
So far no problem with nRF51422QFAAC0.
Upgrading to Keil MDK5 would be a nightmare, so that I gave up after a few days...
Hi,
I'm trying the nRF UART example but I can't get it to work.
I have opened the uart_example project in uVision and loaded it to PCA10001.
Then I opened the Master...
I want to add timer to send sensor movement data to PC every 8ms(125HZ).
But when I add app_timer like normal
1.raise APP_TIMER_MAX_TIMERS
2.raise APP_TIMER_OP_QUEUE_SIZE...
I am testing Keil MDK5 and created my own simple nRF51422 project (not from the sample), hello world type of code. But the "download" button is disabled.
The J-Link is configured...
Hi,
Can anyone please tell me the exact way to enter into the bootloader mode by writing some characteristics with specific value.
I tried setting
NRF_POWER->GPREGRET...
The existing Master Control Panel cannot be used as an automatic test platform.
Basically I am looking to send commands via a tcp/ip which will invoke scan/connect/disconnect...
I'm trying to measure a scaled down battery voltage level on an ADC pin. Given my resistor values the voltage on the pin should be about 0.279 times VBATT, to fit within 1...
Hi Nordic guys,
How much is the current consumption of the LDO only (quiescent current), without DC / DC converter, in uA? How much is dropout voltage and PSRR (ripple...
I try to modify "ble_app_ibeacon" sample code. But when I add some adv_uuids for services to advdata.uuids_complete or I changed advdata.name_type from BLE_ADVDATA_NO_NAME...
Hi,
I need to write a validation document for nRF51822 . The first step need is the specification for its calibration. But I couldn't find it in your website. Can you send...
Hello,
My project name is Remote Operated Vehicle. Basically i am using a PS2 controller as the joystick to control the car. So, my aim is to build wireless interface between...
In this function in nrf_gpio.h, why is there a GPIO_PIN_CNF_INPUT_Connect value there?
Shouldn't that be GPIO_PIN_CNF_INPUT_Disconnect, or does it not really matter?
...
I need to pass a bit, to 500 recipients in a closed room.
My doubt is, 500 receptors works simultaneously without interference?
Ref. to buy:
www.ebay.com/.../251458486443...
