Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi,
why antenna trace is connected to mounting pad instead of feeding pad of antenna in thingy 91x
We are designing our device based on this. We wish to be sure about...
Hi,
my name is Nick De Leenheer, and i am finishing my thesis on indoor localisation with CHANNEL SOUNDING. i currently got these outputs in my venv using SERIAL: so i...
Hi all,
I want to fully understand the concept of Bluetooth protocol using nrf52811. Any advice will be helpful for me!
First, as I understand softdevice is Bluetooth...
Hello
Does the green box directly determine which version of the lib to use[ lib_openthread_mtd.a ]? If so, what is the purpose of the red box? If I change the red box to...
We are currently working on a project using the Nordic nRF5340 and nRF7002 DK, which includes 1MB of internal flash and 2MB of external SPI flash. Our application codebase...
Hi there,
I'm working with a custom board based on the Raytac AN54L15Q module and encountering higher-than-expected power consumption when trying to profile using the system_off...
Hi,
1.In ncs v3.0.0, can both USB DFU and UART DFU be enabled simultaneously on the nRF5340 DK board? 2. If USB and UART DFU can be enabled simultaneously, then how should...
Development board: nRF54L15DK i I'm already using "Find My Example" to connect to the "Find My" app on my iPhone. At the same time, I also want to connect to nRF Connect....
Hi,
there is my project rom size in memory report , I would like to asking what is the "NO Paths" item and hidden item
they hold my 20% ROM size. and what is the content...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello Nordic support team,
Forgive me if I am asking a stupid question.
In the source file ble_conn_params.c, there is a function called ble_conn_params_init() and I...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hello Nordic,
We have recently purchased an nRF52840 Dongle. We were able to sniff the BLE packets over the air. So it is found that all the packets that we are able to...
I was implementing custom services and characteristics(softdevice:s140, ble) on the nrf52840 dongle, however I couldn't get it to work, even though my code seemed correct...
Dear All,
I updated Toolchain and SDKs to last version v3.0.2 and I'm going to add build configuration as suggested here How to create and build an application .
My board...
