Hi, in the example bootloader in sdk 7.2, there is an assembly code block in SVC_Handler, in dfu_ble_svc.c.
I found that the offset in line:
LDR R0, [R1, #24]
always...
In nRF51 SDK 7.1.0, there is a c header file using c++ keywords operator .
Here is a snippet of components/ble/ble_racp/ble_racp.h using the keywords.
/**@brief Record...
I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
I need to pass a bit, to 500 recipients in a closed room.
My doubt is, 500 receptors works simultaneously without interference?
Ref. to buy:
www.ebay.com/.../251458486443...
I've seen various threads here with sample code attached that show how to set up a timer to measure a battery voltage periodically. They also seem to use an external crystal...
Dear Nordic Guy,I'm developing with nrf51822.
my costom code based on the hrs profile.and I modify the advertising timeout value to 30sec
and finally, I see the a few uA...
Hi,
I bought the nrf51822 chip itself, and created my own board. Now, can I still download the nRF51 SDK as per nAN-29?
I am stucked with the download page asking for...
Guys
I came over from the Arduino forums, I am searching for a new RF chip to use for a project i am working on but dont know which chip to pick. My application requires...
I want use uart to debug my ble program ,
In the devzone I found this and this to meet my need , but when I conditional compilation UART code into hex, I can not find my...
Hi All,
I am trying to use the HRM_RX sample code with my Linux PC side application. but i am not able to receive any UART RXD interrupt on nRf51422. I checked PC is sending...
We are developing a BTLE perihperal product using nRF51822 chip. But we would like our product can be up-gradable. So we will need a Bootloader (by UART or other interface...
while creating a Makefile for DFU, for BLE DualBank only, I'm getting some odd errors:
../bootloader_util_arm.c:19:1: error: 'at' attribute directive ignored [-Werror=attributes...
SDK v5.1 /v4.4.2
Keil 4.73/Keil 5.1
delay function seems doesn't work well in new version of keil. But I need it to bebug and flash nRF51822 with new keil.Need your help...
I would like to use an nRF8002 in a proximity detection application.
I would like to be able to send a request/command to the device to start a continuous or rapid transmit...
This may be an obvious question, but I wanted to make sure that my assumptions are correct.
The nRF51822 is able to use an external 32kHz crystal oscillator for its low...
In the 51422 Prod Spec v2.0 it states that “high performance RF capacitors” for the X7R decoupling caps should be used.
Is High performance RF equivalent to a “High...
Hi,
I am trying the Direct Test Mode (DTM) function integrated into the nRFgo application. I am using the nAN-34, Dev Kit User guide, and help (F1) in nRFgo as documents...
