Hi Sir,
As we know the nPM2100 support AA/AAA batteries, LiMnO2 coin cells (e.g., CR2032), Alkaline coin cells (e.g., LR44) .
But could nPM2100 support CR123A 1S2P?
...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
This test program is modified from examples\pin_change_int\main.c, I add the instructions to put the cpu to sleep. And I add nrf_gpio_input_disconnect() for all the pins except...
Hello, I am using pstorage function and I would like to know oppionions of your's what would be the best practise to wait until processor erases the flash memory and would...
Is enable required before configuration? Does toggling NRF_ADC->ENABLE reset the configuration (like it does for the radio?) Is the power to the ADC automatic, so that even...
im using sdk10, I initialiszed ble_stack_init and advertising_init but when starting advertising, it works with BLE_ADV_MODE_FAST but not with BLE_ADV_MODE_SLOW .
why it...
Hallo comunnity
I have a sensor which is working is sending data via BLE and it has a 128 UUID bit service [0x 000000-000000-1000-8000-0080-5F9B34FB]
In order to do...
Hi,
What is available MTU of CoAP and UDP over 6lowpan with IoT SDK ?
In my application, I need to transfer dozens of kb data to ble node over 6lowpan with iot SDK. Do...
Hi, I bonded is ok .But I want to store some data on nrf51822 flash memory using pstorage. What should I do?
Register new or change it :
param.block_size = ALL_CONTEXT_SIZE;...
I have an SPI peripheral that has an odd protocol and in trying to sort out why it was acting up I finally caught a logic trace showing about a 13us break in the SPI data...
Hello,
I am using HID mouse/keyboard examples from SDK to learn creating custom HID device.
Besides using four buttons on EVK to simulate motion action. I would love...
Hi All,
I'm currently setting up three nRF52840 DK nodes, two nodes are routers and one is an end-device. My plan is to introduce more node in the network later on. The...
Hi,
We created a faster & simpler alternative to gazell for the nRF24LE1 (our IoT sensor) that supports 100s of transmitters (PTXes), is individually addressable, has session...
Hi
I'm using the NRF51422 with hardware UART.
Brief outline of the configuration:
115200 Baud, 8-N-1, no HW flowcontrol
SoftDevice S130 V2.0.1
lib: app uart fifo
...
Hi all,
I am using the softdevice S130 v2.0.1, plus one application derived by the ble_app_uart and the single bank bootloader (SDK11) on a custom board with the nRF51822...
