I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello folks,
we setup a new Project (eclipse,SKD 12.2.0, S130, NRF51822QFAAH0) based on the sdk examples. But the thing since 2 days we got a error we actually do not understand...
I have a PCA10040 board and downloaded SDK 12.2.0.
I am trying to being a project based on experimental_ble_app_eddystone. I can compile and upload the code to the board...
Problem:
IAR compiled hex file does not work for ble_app_hrs
Environment used:
IAR Embedded Workbench for ARM 7.80 Kickstart evaluation
nRF52 DK
Observation...
Hello,
I use, with success, the FDS library to save data to the flash memory. I also use, with success, the bootloader to update the application (original dual bank ble...
Hello there, thanks so much for taking the time to read. My problem is the following
I am trying to run GZP (Gazell Pairing Library). After successfully pairing with a...
We are currently trying to log our sensor data to a mobile phone through uart using nrfLogger app. We have nrf51 module and we are using SDK 12.
In nrfconnect, we select...
Hi,
I have problem with long write by sd_ble_gattc_write.
I send first 18 bytes by button on pca10028, then I waiting for BLE_GATTC_EVT_WRITE_RSP and sending rest of bytes...
I need some help with something very basic...
I need a way to upgrade my DFU BLE bootloader to either reset back to the app if no update has been sent after some timeout...
hello,
According to the "twi_scanner" example from the SDK12.2 I don't understand how the respective I2C pins/GPIOs are set up.
There is this function that I found "nrf_gpio_cfg...
My nRF52 device is an asset tracker and does not have a comm port. I have been looking at a BLE dongle setup for manufacturing test but the results are not repeatable with...
HI,
Nordic part used is nRF51822.
Is there any way to increase signal strength of BLE tx?
I see some parameters in advertising_init function for advdata.p_tx_power_level...
Hi all
According to chapter 50.2 of the nRF52832 product specification V1.2, the pins used for the UART peripheral should be configured before in the GPIO peripheral to...
why most of the examples of sdk 12's sdk config file has different options?
I'm trying to build an application that has Central and Peripheral Role application (and it...
Hi,
I have noticed the new preview DK for NRF82840 is now available, and the new chip is running the new BLE5 spec. My understanding on the BLE v5 is the higher data rate...
Dear Team,
We are facing an issue in nrf51822. We are compiling same project on different system in log file we got certain differences such as
System Licence
...
