Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
The documentation simply says: 1 for variable length and 0 for fixed length.
What exactly does changing this do? Do I save space by setting it to fixed? Why does BDS set...
I don't understand why i have a current consumption of 0.535mA in system off.
In my soft i use PWM, SPI a Button,, I put all things off before i go to system off but still...
hi all:
I download the nRF OpenMesh from the GitHub.
There are 4 example in this folder:
(1)Bandwidth_test
(2)BLE_Gateway
(3)ping_pong
(4)Template project
I prepare...
Hi,
Starting from the LED Button Service found in SDK_12.2.0/examples/ble_peripheral/experimental_ble_app_blinky I'd like to add two characteristics on this service. I...
Hello!
Based on you example I try to develop a simple HelloWorld example that follows chapter 11 of the specification. It says that to form a network a energy scan should...
Hello,
I have been investing a couple days now in order to get the DFU procedure working properly, but it seems I am stuck...
This the setup that I am currently using...
Hello,
I seem to be having some errors with my current project. I am using SoftDevice S310 Version 3.0 and SDK 9.0. When i try to communicate with one of my I2C sensors...
Hello,
When using hal_w2_read() and hal_w2_write(), should the 7 bit address of the slave be passed in or the 8 bit read/write address?
It seems to me that passing in...
I downloaded the nrf52 SAADC Low power project from the GitHub
github.com/.../saadc_low_power
I'm trying to migrate it over to version 12 of the SDK and I think I'm having...
Hi. I'm using nRF52832, SDK13, S132V4.0.2.
I'm trying to test DFU.
I have 2 questions.
Q1. How can I make image for merged files?
I can see it works very well when I...
I am in the process of porting an nRF51822 (s130) project to the nRF52840 (s140), moving from the SDK V11 to V13.
I was using the BLE_EVT_TX_COMPLETE event in the SDK V11...
I've seen in two different posts that some people were trying to use this Torex XC9265A181MR-G in terms of being able to use a 3.7V LiPo battery. Can someone tell me if he...
I just bought the NRF51DK and going through this getting started guide: devzone.nordicsemi.com/.../
I opened the file ble_app_uart_pca10028_s130.uvprojx in folder ..\examples...
Guys
I am a newbie using nordic modulesI am just starting to program here with a nRF52 and SDK 12.2
I was trying to edit the experimental_ble_app_blinky and experimental_ble_app_blink_central...
