Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
Hello.
After executing the code below, the RAM was dropped and the program could not be written.
for(idx = 0; idx < 7; idx++)
{
NRF_POWER->RAM[idx].POWER = (POWER_RAM_POWER_S0POWER_Off...
I'm studing the project of ble_app_gls/PCA10040/SDK11.0/ ,I have got some questions about the RACP indication pending and retransmittion mechnism. In this project(File ble_gls...
enter code here Hi guys I have managed to program an example BLE_Serial program into the nrf51822 but I cannot see anything coming out from the TX and RX ? Please guide me...
I've tried to install nRF Connect v2.0 on both Win 7 and Win 10 systems, both running Avast Anti-virus (up to date). In both cases the antivirus gives a warning about IDP...
I have the Memory Manager module enabled in my custom sdk_config. Within the module, I have both of the following defined.
MEM_MANAGER_ENABLE_LOGS 0
ENABLE_DEBUG_LOG_SUPPORT...
Hello - Is the long range option programmable in BT 5.0? During the run time, is it possible to switch between high speed and long range mode dynamically depending on the...
I am specific about master as I have to connect two simultaneously(obviously to two different pins pair). Plz provide any code outline if you have, Thank you in Advance
Hi.
I would like upload firmware from Atmel microcontroller to nRF51822 with SD130.
I suppose that I have to use single_bank_serial_s130 in nRF51822AA, but what I have to...
Hi,
I'm trying to implement dfu bootloader over uart, not dfu bootloader over air.
Where can I find a reference source code of dfu bootloader over uart?
regards ...
Hi,
We have to find the battery life of a central device based on nRF52 (s132 v3 soft device)running with 800mAh battery. The device scans for a peripheral in every 5 sec...
Hi!
I am trying to measure the current profile of a pca10056 board using an oscilloscope. I cut SB40, as per instructions in the User Guide and powered it using only a...
Hello,
Are there any rules for how to use the manufacturer specific ID in a beacon-format advertisement? For example:
In this example:
byte 0-2: 02 01 06 = flag...
I've used DFU alongside with HRS and it seems to work fine.
This time I'm using a custom service and I'm trying to add a DFU alongside. They just don't seem to play well...
Hi, I successfully modified the Nordic Semiconductor SDK 13's SAADC example adding a feature that performs the FFT of the sample taken and using an RTC is possible also to...
