I have been testing the thingy91x and measuring power consumption trying to reduce it to the absolute minimum.
Using a test program that moslty sleeps ( using k_sleep()...
Hello,
I'm working on a project using the nRF52840 and Zephyr, and I'm experiencing an issue when trying to use device power management (PM) with a custom sensor driver...
Hello,
I am new to nRF development. I am going through the nRF Connect SDK Fundamentals course.
I wanted to configure a GPIO on the nRF52833 DK board as an output and...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hi,
i acheived writting code that reconnects sequentially with multiple reflectors for my 1 initiator. When i am indoor i had good results, but yesterday i tried it with...
Hi,
I'm new in Bluetooth an I want to try a "simple Project". I've connected 3 Peripherals (all nRF52832 Chips) with 1 Central (also a nRF52832 Chip) together.
With the...
Hi everyone, In the Power Management example, why the HFCLK still running when the uC is in sleep mode ? I see it in the HFCLK_STAT => State = 1 Shouldn't it be disable to...
Hello,
I have been using nRF development boards for a while, but recently I am currently unable to program my nRF52 development board, due to driver issues. The following...
I am trying to make TWI calls from an APP_TIMER event. However the TWI calls are failing. I can see that the twi message is sent on an oscilloscope, but the function never...
Hi,
I got the same error as the guy in this question: https://devzone.nordicsemi.com/f/nordic-q-a/26041/compiling-error-for-nrf51-development-dongle
I use another example...
Hi, I would like to use a nRF52 demo board, to test nRF BLE with a HX711 and screen. The nRF module is powered 3.3V but the HX711 and the screen are 5V powered. Is the bus...
Hello,
I am in the process of evaluating the '840's BLE and CryptoCell for a low power application. I am using a modified version of the ble_app_template example, with custom...
Hi guys,
I have custom MAC address that saved in the flash. I used the sd_ble_gap_address_set function to change the Mac address to my custom address.. I found out in phone...
Hello,
Is there any option in nrfjprog to force a Segger's JLink to power the target? I am able to turn the power-out feature on using JLinkExe buy I don't whether nrfjprog...
I refer to nRF52810 product specification v1.1 In all reference designs, C6 is N.C.
I would like to know why this is the case?
I would also like to know why it is included...
Hello,
I am using nRF52832 DK for my project which is to receive data from arduino and send it to a smartphone using BLE. My issue is that i make nRF52832 to enter Bootloader...
I have nRF52832 as my development kit. Currently I am testing various ble peripherals i.e Blinky , beacon etc. Now I have to test IR sensor with the Development kit .I aim...
Hello,
I used a the ble_app_template example to set up advertisements on the PCA10040 board and on our custom board. Both boards function and have good signal strength....
I build ADC example from SDK12.3.0 for nRF51822 QFAA chip from source. I used custom board and changed the pin configuration for UART logging in sdk_config.h file.
But unfortunately...
Hi All,
I am performing OTA-DFU - Generating our own packages on my nRF52DK. but when i am trying to generate zip but i am getting some error , below is the screenshot for...
