It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
Hello,
For our emission tests in an anechoic chamber we need to be sure that the BT antenna is up and running. Of course we cannot connect via BT from outside the chamber...
Does anyone know when will ANT SoftDevice be available for nRF5 SDK v15? Accordign to https://www.thisisant.com/developer/components/nrf52832#tab_protocol_stacks_tab, only...
Hi
I try to communicate with my NRF24L01+. For this, i have connected a mikrocontroller to my Module. Actually i am using a small piece of code, which allows me to send...
Hi,
In my project, I use button for put on the microcontroller in sleep mode. I implemented one timer that when I press more of 5 second the button, the micro call sleep_mode_enter...
Hi,
I have included in my code the code from the twi_scanner example as a starting point for using TWI in my board. When compiling, I get the following error:
../.....
hi,
Please Refer Light Switch Client Example in Mesh 2.0
I would like to know Code where and in which File the UUID from the unprovisioned Node is captured ?
Thank ...
Hello,
What is the switching frequency of the buck regulator integrated into the nRF51822?
The characteristics of this regulator do not seem to be explained in the documentation...
I'm following the Custom BLE Service Example , and using:
Segger Embedded Studio Release 3.34a
macOS 10.13.4 (aka High Sierra)
nRF52 DK (PCA10040, nRF52832)
nRF5_SDK_15...
Hi,
I am investigating an alternative to an implantable device that currently uses NFC.
The device range would only be about 3m and the data would only be transmitted...
this packet is capture by wireshark .I use nrf51822 and sdk12.3 connect Balance car,but the packet not have LL_VERSION_IND, LL_FEATRUE_REQ、and LL_Connect_UPDATA_REQ these...
Dear Nordic Team,
Thanks for supporting.
now i am workwith secure dfu. I followed this link https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure...
hello
I am just starting to use the nrf52832 .
I design the PCB with nrf52832 and want to load the softdevice.The nrf go studio can not detect the nrf52832, but the keil...
I was facing some issues getting PWM peripheral work on my custom nRF52840 board. And then I tried the pwm output on P0.08 instead of P0.06 and the signal came out just fine...
We're developing a new device for a regulated market (medical). As such, we need to have control on what third-party software we're using, and how it is working. While starting...
I wanna implement this code for the app inventor, but there was several problem here. I can't use array or index for developing my trapezoidal method.. like this..
code...
