Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
I am building a Central BLE app using the Rigado BMD-200 but my current peripherals are running RFDuino code. The peripherals all work with the IOS and Android Apps but I...
I'm using a snippet from the ble_app_uart example and see in the examples:
//static ble_uuid_t adv_uuids[1];
static void advertising_init(void)
{
uint32_t err_code;...
S110 v8.0.0
SDK v8.0.0
ble_app_uart example
I first initialize the services and then initialize advertising. Everything works fine when I do NOT advertise the...
I'm currently trying to make an application using the development kit & I'm trying to use the timer driver, when I induled the C & H files of the driver I got an error : ...
I'm trying to compile the ble_app_beacon_s110_pca20006 project in Kile uVision5 and I get the "cannot open source input file "core_cm0.h": No such file or directory" error...
I am trying to run a NRF51822 chip using Emblocks and OpenOCD, the debugger interface is a ST-Link from a Discovery board, which supports SWD.
When I program the Blank...
Hi,
I bumped into a problem trying to get PWM working and traced it back to the app_pwm_init function, for a simple test case use the the pwm example in the 8.1.0 SDK and...
Hello everybody,
I'm currently trying to start with the nordic development kits, I installed all the tools required to be able to start the development & also I get some...
I am trying to persist characteristic data written by the central side after on_disconnect . I can see the data written inside the evt_write->data ptr and I copy it to store...
Hi Nordic Expert,
Recently I wanna run ble_nus service on my nrf51822 platform, you know, sdk 6.0 does have this demo code in s110 directory, but from sdk 6.1 I cann't...
I'm trying to connect to/program my nrf51822 module I just got. I've got it set up with my st-link but whenever I try to flash the device I keep getting: Error: Flash Download...
I'm trying to enable basic commands with my device. Ideally I have a terminal open on a mac running nodejs or use the UART subapp in the nRF Toolbox App, type a special command...
What's the proper way to debug what's causing my eval board to reset? I'm assuming I need to put a breakpoint in the hard fault handle, but how do I trace that back to the...
Hi,
as a university project, I am currently developing a ultra-low-power temperature and barometer sensor powered just by RF and laser-beam energy. Please see this link...
