Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
How to change Peripheral Role to Central Role without having concurrent Role?
I know S130 Can have 8 Concurrent Role as Central, Peripheral, Observer, Broadcaster.
But...
Hellow i am starting with nrf51, and reading nAN-36_v1.1x.pdf doucument
about using use a button to sent a signal through ble.
the BLE hellow world.
but I cant find the...
I'm trying to program 500 raw (not populated on boards) Taiyo Yuden EYSGJNZWY modules, which uses the nRF51882 chipset.
Does anybody know where I can get a fixture to do...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
Long story short, I need to create a packed struct.
I knew the pragma way, to change aligment, didn't work.
I looked up and found the __packed (I'm using Keil µVision...
Hi,
I am planning two have the following network:
1 central communicating with 3 peripherals
One of the peripherals will be a smart device (iOS or Android). What...
Using SDK 12.2, I have compiled the secure bootloader successfully, tweaking the sdk_config and Makefile to use RTT for logging and turning on logging, and using the "_debug...
Configuration: Nordic PPK, PCA10040, PC10028 & PCA63511. Current consumption is relatively high on nRF52 vs nRF51; nRF51 is configured with SDK 10.0 and nRF52 with SDK 12...
Hi,
I have got my nRF52 DK. I could flash softdevice using nrfjprog.
But after reading s132 specification, i have following doubts.
How to flash application from the...
Hi all --
I have an application where I have a LDO generating 2.6V from a single lithium-ion cell. It has an EN input that I want to expose to the nRF52 with a little RC...
Hi,
I'm searching for the nRF52 Ref Manual. I've located the Product specification for the nRF52832, but can't seem to find anything for the Reference Manual.
I found...
To maintain compatibility with our current systems we would like to be force characteristics to be at certain handles, rather than having the soft device assign them sequentially...
I am upgrading from v12.0 to 12.2. I am using Linux, Eclipse, GNU ARM and Eclipse managed make.
I get compiler error ...nrfsdk12.2/components/drivers_nrf/hal/nrf_gpio.h...
