This previous question about multiple advertisements seems to be related to softdevice 7. I was unable to get a similar example working in SD/SDK8
My end-goal is to add...
We are considering using Gazell for an outdoor application, i.e. lots of noise and disturbances, constantly changing environment, where the amount data being transferred is...
Hi everyone,
I have found your git "Ble Optiboot"( github.com/.../ble-optiboot) , and I have understood, it is usefull to load a binary into MCU flash, I was looking for...
I'll go ahead and describe what I need to do and see if anyone might have some place to start for me since I'm having a lot of trouble figuring out what I need.
I'm looking...
Hello ,
I'm designing an embedded system with one of your RF chips (NRF24L01+) and as far as I searched for the datasheet , It seems like NRF24L01+ doesn't have a hardware...
Hi,
This post is very old.
devzone.nordicsemi.com/.../
I have a nrf51822 chip and I'm using it as BLE and it exposes some service and characteristics and it is working...
Hello!
I set up a project using NRF24L01 and a patch antenna ceramic, the type used in GPS.
In fact, I tested several types of antennas, F, F inverted, GPS, Loop. But...
Hi there,
I was trying to understand "sleep" power modes of the chip (CPU + Peripherals) in a bit more details - but my understanding is that everything is handled by the...
Hi,
I am facing some issues on enabling timer1 with s132 (nrf52832 pca10040) enabled. i am using the basic timer0 example code as reference and it was working without the...
Hello,
I would like to use fstorage function, but when using the example of sdk 14.1.0,
I had some errors, please help to let me know what problem is and how to define...
Hi all,
I've got a single Thingy:52 (FW v2.1.0), and no DK. I'm trying to upgrade its firmware through nRF Connect on Android, but keep on running into a FW version failure...
Hi to everyone!
I have a custom board (based on nRF52832) with two LEDS and other GPIO ports. In some point of the code I have to activate one device by setting one port...
Hi Guys,
Will they work at the same time?
i want to use the MCU for UART and at the same time i want to run the BLE GAP events parallely.
is this possible? and how...
Hi all,
I have two pwm pins I would like to have them run at two different duty cycles. My understanding is that we can do this by setting the decoder to individual. When...
Hi, We are facing issue related to pc_ble_driver shared library at the time of run script.
Traceback (most recent call last):
File "SDFTest.py", line 414, in
init...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
i'm developing an application with the NRF51822 device using the NRF51 development kit (DK). I bought a power profiler kit (PPK) to measure current for advertising...
I am using nrf52832.
I am setting MIN and MAX Connection Interval both to 7.5 ms as android support 7.5 ms connection interval. We are getting 2-3 packet in one connection...
We are in the process of upgrading from from soft device v 2 (with SDK v 11) to soft device v 5 (with SDK v 14), and we have a portion of our code that controls connection...
Hi averyone,
We are developing the BLE project whith two devices master/slave.
The master device is built on the NRF52832 processor with SDK14.1 and it's program is built...
nRF52832 is in a sleep state.
However, when the Watchdog timer clear processing is placed in a different position, current consumption changes.
If the Watchdog timer...
