hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hello
No reply so I am writing again. The LCD operates normally using the source as shown below.
https://github.com/Exboom/GC9A01_nRF52
However, the screen does not...
We are currently working on a project using Enhanced ShockBurst (ESB) and would like to enable Front-End Module (FEM) support with the nRF21540.
According to the Enhanced...
Due to production requirements, I need to obtain the device's QR code. However, I found that the QR code can only be retrieved using the code snippet below after calling Nrf...
Dear All,
I updated Toolchain and SDKs to last version v3.0.2 and I'm going to add build configuration as suggested here How to create and build an application .
My board...
Hi, I have issues configuring PSM together with RAI on my nRF9151-DK. I am trying to send UDP packet, wait for response and go to sleep for several minutes trying to consume...
I'm having trouble porting my project from the older SDK (2.6.0) to the new SDK.
I thought the most straightforward way to do that would be to start with a sample project...
Hello
I get the following error code, when I try to build the button sample with my custom board. I try to build and flash via RTT Hello World with my custom board and it...
Hello,
I am using the nPM PowerUp application with the npm1300 Evaluation kit. I am trying to configure the bucks (1 and 2) to be on/off controlled by one of the buttons...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hi Support Team
Could you guide us build an efficient automatic programming tool for nRF54L15’s mass production? Our Apple Find My and Google Find My project will be mass...
Hi
We have a Nordic thingy device with us & using that we would like to perform some network testing.
We are setting up a private NB IoT network and we would like to...
Hi,
1.Please provide the documentation, examples and tools for testing the RF performance of nRF7000 during the mass production of nRF9151 + nRF7000. 2. If not, please provide...
Dear colleagues, I am using the Nordic nrF9151-DK as part of exercise1, lesson 2 of the intermediate Devacademy course. Lesson 2 is about trying and using the various vscode...
Nordic #Devacademy intermediate course: Ticket for exercise 1 of lesson 3
Dear Colleagues,
I passed the test for lesson two, with only getting exercise 1 to work. Now...
Hi,
I am currently working on a two way communication between an nrf52840 thread host and an nrf52840 thread client over coap. I have nrf connect sdk version 2.9.0 in both...
