Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hello,
I've a battery based device that uses a buck/boost to efficiently use entire battery voltage range (4.2-3.0) . This component have a low quiescent current between...
hi support team,
I was testing 7002dk with a Asus router，i found two questions:
1.5340tfm jump to application taks about 8 seconds, why it takes so much time?
2.7002dk...
I’ve designed and fabricated two custom boards around the nRF52840 SoC.
I use an nRF52840 DK as an SWD debugger to communicate with each board.
Using nrfjprog...
LE audio can support multiple stream, but I can't find any description about following application, please advise....thanks
phone1 use unicast to play audio on headphone1...
Hello,
I am trying to connect to the PPK2, but I see on device manager stating that the PPK2 needs drivers to be installed. I have nRF connect v5.2.0. I have tried uninstalling...
Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Hello, Has anyone implemented Deep sleep in nrf52833, v2.9.0?
What all I tried :
1. tired to use "pm_state_force(0u,&(struct pm_state_info){PM_STATE_SUSPEND_TO_IDLE, 0...
I want to implement deep sleep (wake up using RTC at a particular time interval), and determine the current consumption in nrf52833 dk. So I used the sample code first. When...
Hi,
I would like to know the difference between the nRF52840-QIAA & nRF52840-QIAA -R7.
What is the significance of R7 here. Not able to find it in any conclusion ...
Good afternoon! As the NRF7002 takes about 400ms to start up from shutdown, we would like to use the very low power deep sleep function for quick startup. Unfortunately, due...
Using latest SDK and toolchain 3.0.1, VSCode and nRF Connection Pack on Windows 11 I nearly never see a working nRF Kconfig GUI - only the first time directly after I had...
Hi,
I have a custom board for the nRF54L15. I have already implemented LEDs and a button, which work fine. But I cannot get the PWM peripheral working, and I do not understand...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
Hi, I'm working with the DWM3001CDK (nRF52833 + DW3110) and currently using SPI to interface with the DW3110 for UWB communication.
I'm trying to use a second UART to communicate...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
