Hi,
We have a device using the S110 v6.0.0 softdevice and the SDK v5.2.0.
We started working from the Proximity application available in the sdk.
Is it possible to...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I have a simple demo device that does play to be a mouse and a keyboard using HOGP profile. I can get it running with Linux pretty well and I can get it running with...
Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
when a particular line of my code is at line 54, the following compile error occurs:
error: #101: "assert_line_54" has already been declared in the current scope
line...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
hello,
On a device with nRF51822-CEAA packaged in a ISP130301, we have a problem with RSSI value measurement.
We use Master control panel and bluetooth usb key provide...
I have set up raspberry pi 3 as a border router and programmed the the nrf51422 using the iot_ipv6_coap_server_pca10028 and could successfully switch on and off led3 and led4...
nrf51822QfAC
S130 stack was working fine and ble_app was able run successfuly able to see the ble on the app;
Now after few days now facing issue in running the same code...
having issue with nrf51822
nrf51822 breakup board was running fine with S130 2.0 stack and ble_app_uart
Now facing issue such that when softdevice enabled is called the...
Hi,
I just switch to Embbeded Studio following the last tutorial ( here ).
I'm working on NRF51822 with SDK12 and TWI_sensor example (without SoftDevice). I followed...
I see from the release notes of s132 4.0.0-2.alpha that it adds:
Support for 20 links in total with freely selectable role (Central/Peripheral) for each link.
I want...
Hey,
I am trying to control an external LED using two nRF52832 boards. I am using "nRF5_SDK_13.0.0_04a0bfd\examples\ble_peripheral\experimental_ble_app_blinky" code for...
I'm trying to use the BLE sniffer in a quite busy BLE environment. Unfortunately, it always crashes after a few seconds.
I'm using:
ble-sniffer_win_1.0.1
nRF51 Dongle...
Hi,
i am using PCA10040 DK board,
working on ble_app_Uart example, i have created one timer(app_timer) here is the code:
printf("init\r\n");
ret_code_t err_code;...
Dear all,
My chip is nrf52832, and sdk version is SDK12.1.0_0d232a. And tried to use ble service and spi master function.
I create a timer to send spi command every...
hello all:
my mcu is nrf51822(QFAA), and use it to make a blue device ,i want to use mcu's reset pin to reset it, just use hardware. i add a key to connect the reset pin...
