Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi all!
My question is:
My own application is built based on the example "ble_app_template", and according to the nrf51 SDK - Examples - BLE Peripheral, this example...
Hi,
I am using ancs service to get some information of my iphone.
I use nRF51822 microcontroller and Nordic suggests to use the new SDK (5.2) for new microcontroller...
Hello
I am testing with the lis2dh12 sensor and our custom board. I made the LCD test successfully. So I tested the lis2dh12 sensor based on the LCD code, but it failed....
Is there a comprehensive explanation of the usage of uuids_complete, uuids_more_available & uuids_solicited when to use them and how the stack behaves/uses them. I getting...
Hello
First of all, I would like to apologize if a similar question was already asked but all this BLE matter is so broad that it defeats me.
I am planning to put two...
I try to use Eclipse for my nrf project. Previously I used Keil but now, I should to use Eclipse. Anyway, I can build nordic sdk example project but when I work with main...
Hi,
I have posted the same question in the following URL.
devzone.nordicsemi.com/.../
It will be very helpful if you tell me how to get a correct MIC result by AES...
Hello,
I've got some trouble using Nordic Uart Services,
I correctly add the library to my project.
I can receive data from different devices. But when I want to...
Hi, everyone,
I develop the project on N52832 chip when the chip "plays" central and peripheral roles together.
During the running the program I need to check the advertising...
Hello. Everyone.
I'm Aaron and beginner in nRF52832.
I have some serious problems with using the nRF52832.
I'm trying "ble_peripheral\experimental_ble_app_blinky" in Keil...
Hello,
I am using 14.1.0 SDK, I implemented the custom service and characteristic,
but if adding CCCD(Client Characteristic Configuration Descriptor) with the custom value...
Hello,
I am using nrf52 and sdk12.2.2. Can I program this with bootloader and application image at once using nrf go studio?
At present I am first uploading bootloader image...
Hi,
I have 3 nrf51822 devices. Two of them act as peripheral and one acts as central. Each peripheral is used in a wheel and they are the 2 wheels of a cart. Central is...
We are trying to connect RF51822 with RaspberryPi over Bluetooth. Our aim is to get Light sensor values(lux).
Please advise how to get started with RF1822 Sensor.
*) How...
Hi there~. I tried Nordic's FFT example (SDK 14.2) with a PCA10040 board. So I tried to add that FFT related codes in the heart rate peripheral example. I use the Segger's...
Hello, I am practising and studying the beacon example on nrf52840. While reading the main code, I try to delete the log_init part, however the kit doesn't advertise. I am...
