I need to create timeout below 1ms. I would pretty much like to use timer for that because I do not want to hold the cpu inside cycle. For me it is not important the exactness...
Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hi
I connected RF Connect for Desktop to "nRF54L15_DK" in my Desktop
when I want to use Direct Test Mode,press Start test bottom,the log show "DTM setup reset command...
Performance on hardware (cc3xx) is significantly slower than performance on software (oberon). Does anyone have a good explanation for this? I have also tested ECDSA and can...
Hello Sir,
I am currently working with the boards:52840dk and ncs:2.9.1
Regarding the issue of failed mcuboot upgrade after writing the upgrade firmware using flash APIs...
I run the system_off example without the system actually going off, by removing all the calls to start the system_off worker. Instead of going to off, I let the system enter...
I have this main code:
With this overlay:
and this configuration:
I am using a nrf52840 dev board and have connected P0.06 and P0.08.
Why does it not trigger...
I'm playing a bit with MCU boot and folowed the tuturial . When I compile the sample with mcuboot from Zephyr, it works fine for the 52840DK, but when I try to compile for...
NPM2100 EK CONNECTION
Can I connect The NPM2100 EK with NRF52 DK? If so..... 1. How do I physically do this? 2. Can I program the NPM2100 EK to send Voltage Supply of 1...
When using Bluetooth AOA, I configured only two antennas to collect IQ data. Below are the curves formed by the 37 IQ data points collected from the two antennas during the...
Dear Nordic Teams :
I find the NFC current and find the current is quite large in the datasheet version 0.8. The value is much bigger than nRF52840. Is it correct?
Hi,
I would like to clarify a few points related to the power saving modes of the nRF9160 and how it behaves in low-power states.
1. PSM Current Consumption — What Does...
Hello everyone!
The Quick Start mentions that the two SIM cards that come with the nrf package work right out of the box - I've tried them and they work with just activation...
Hi,
We designed our custom board using nrf54l05, and tried to flash it using segger J-lInk as well as using nrf54L15-DK Debuger out port using nrf connect Programmer utility...
Hi,the nordic Team.
I'm working on the thread protocol.and use the SDK version is V2.9.1.
I have a scenario where my child device is connected to a route or leader. What...
Please help. Why is QSPI not a valid peripheral option?
Environment: SDK v3.0.0 , nRF Connect for VS Code v2025.5.92 , VS Code 1.99.3, Ubuntu 22.04.5 LTS
Code copied verbatum...
I am trying to use the AWS FOTA library. It correctly downloads the image at 100% but always ends with a MPU Fault on the downloader thread.
I set the stack size at the...
