Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I am developing a firmware application that needs simultaneous central and peripheral role. I am using sdk 15.2.0 and was experimenting on dev board PCA10040. I have taken...
Hello,
I want that nRF9160 goes into PSM on boot until a button is pressed, do someone have a good link about PSM please ?
How can I do a software reset with a clean lte...
Dear people,
I use a pca10056 (alternatively the pca10059 dongle) and have compiled the connectivity firmware as described on the github page (release 4.1.1).
The only...
I use nrf5_SDK_for_Mesh_v3.2.0_src\examples\serial and board pca10040.
Supported commands.
In [2]: for i in range(0, 10): send(cmd.Echo("Hello: " + str(i))); time.sleep...
Hi, I'm reading the nRF5340 OPS v0.5.1 document and in section 3.2 ("Memory") there is a reference to "256kB of peripheral RAM". However, the document doesn't explain what...
Hi there,
I'm working on nrf82382, try to use COMP function to monitor the voltage of AIN0(p0.02), but seems not working, no example for the COMP. and then I found the...
We enable TX notification of NUS service with bonded iOS (iPhone), iPhone constantly sends TX_READY command until disconnect.
Can you confirm this is correct behavior. ...
Hi, I am working with the adxl362 sensor and the nrf9160 SPI example ( https://github.com/Rallare/fw-nrfconnect-nrf/blob/nrf9160_samples/samples/nrf9160/spi/src/main.c ) and...
Hi, I am working with the adxl362 sensor on the Thingy91 and I want to set the trigger of the sensor to a specific value.
In the datasheet ( https://www.analog.com/media...
Hello everybody! I'm developing an application using CMSIS DSP library, so i included about 20 math files and using finctions from these files. After compiling i get a linker...
Hello Devzone,
I'm designing a custom board solution that drives a motor using a nRF52832. The board is powered with 4 x AAA batteries and a 2.5V LDO (STLQ50C25R) is used...
My company has a product that is running on the nRF51, with firmware written in SDK9 and sd310. I've been tasked with developing a path to update them to SDK 12.3 and sd130...
Hello nordicsemi community. I'm trying to use the SPIS example provided in the NRF52 SDK to receive data from another SPI master running on an FPGA. I modified the code to...
Hi,
I'm trying to write data to flash as shown in example under nrf5_sdk/examples/peripheral/flash_fstorage, with identical steps.
However every time I call the nrf_fstorage_write...
HI,
I am using nrf52832 with sdk15.2.0 and softdevice s132. I face some issue related MAC address of nrf52832.
when I reset the sensor MAC address of the sensor change...
