I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
Hi, I have a Nordic 52810/PCA10040 DEV board with the latest zephyr.
In Zephyr configuration I using hardware clock option -> 32KHz clock source (RC oscillator)
I...
Hello, I'm getting started with my nRF52833 DK and have downloaded and licensed Segger embedded studio, and nrfConnect.
I believe I want to use the s140 softdevice. I'm...
I am just starting with the Nordic DK52. I am following the beginners tutorial for a custom service . But I am encountering 2 problems:
1) In step 4 it displays a RTT debug...
Hello,
I am trying to convert the twi_scanner into a PCA10056e project following the conversion doc from nordic . This was the downloaded example for the TWI scanner and...
Situation: I'm using a nrf52840 with the nordic sdk 15.2 acting as a Gateway ( Ble Client). On the other side I have four nrf52832 (sdk 15.2) acting as servers. My software...
I am trying to light-switch test different features in my app to see if I can save some memory, and I found that the examples\peripheral\cli example won't compile if I turn...
The bluetooth of android APP is easy to disconnect (we make smart door lock products); The product is delivered to the customer. It is easy to disconnect and not connect with...
Hello,
I learnt about some resource pre-allocation in the datasheet, e.g. ppi, or API documentation, e.g. app_timer rtc1. I see the SDK drivers are trying to take care some...
SDK16, S112, 52810. I have DCDC set up and external 32.768 crystal oscillator on my board.
Here is my code part:
main()
nrf_power_dcdcen_set(true); nrf_delay_ms(100...
Dear ,
Follow the previous ticket, https://devzone.nordicsemi.com/f/nordic-q-a/59034/agps_thingy91
I am trying to use asset_tracker : https://github.com/NordicPlayground...
I am writing an application on a BLE chip that will transmit high volumes of data to an Android phone (520,000 bytes / second signal).
According to some tests I've seen...
my board uses 51822. I am using 52DK to debug it. I have plugged my board with 52DK as following:
RX -> p0.08
TX -> p0.06
My question is, when I init UART in code...
Device: nrf9160 (dk and custom board)
sample application : MQTT simple
segger studio (nordic version): V4.42a
There are 2 main issues:
1) in the main.c file, Segger...