I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
I have shifted from silicon labs for BLE project. In Si labs we have burn BLE bootloader and BLE application separately. Do i need to do the same here in nrf controller? If...
I am unable to detect any i2c device when connected to the Nordic nRF54L15 DK kit. I have change the voltage from 1.8v to 3.3v and Tried and explore other pins in Port 0 and...
Hi All,
I have to implement an I2C Slave on my nrf52833 BLE project which is currently working (SDK 2.9.2)
I need some confirmation with the following step:
I have...
I am using the 54l10 chip, and after compiling the project, I will receive a hex firmware and a zip update package. The bin firmware and hex firmware in this update package...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
The wake on GPIO is working all the time now.
Unfortunately, I want to disable it except when needed.
Here is the scenario:
Power up, pushbutton pin senses clicks...
I am using the nrf52832 and according to the errata v1.1 the same contains a problem in the spi, according to clause 3.13 the engineering versions (QFAA-AA0, QFAA-AC0) and...
Hey..
I'm having difficulties using P1 pins for UARTE0 and/or UARTE1.
configuring the RX & TX pins like this works great:
#define RBP_UARTE0_RX_PIN_NUMBER NRF_GPIO_PIN_MAP...
Hi,
I'm using a NRF52832. I'm looking to measure the battery voltage. I'm using 2XAAA cells in serie (voltage range between 2V and 3V).
Below is the configuration to...
Sometimes, when I want to use the nrfjprog tool, I get the following error:
nrfjprog --log -f nrf52 --reset
ERROR: JLinkARM DLL reported an error. Try again. If error...
I cannot start Power Profiler Kit software. I followed the installing instructions, but ended up with the following:
>python.exe ppk.py
Traceback (most recent call last...
I'm developing for the NRF52 DK (nRF52832) using VisualGDB (which uses SDK v11.0.0).
Right now I'm facing two problems:
1. How do I properly handle interrupts while using...
There are tickets from 3 years ago that claim that nested CRITICAL_REGION_ENTER calls are not supported. Or they are supported if you write your own macros.
It appears to...
Hi there,
When using a PIN as RESET, what is the minimum activation time required to insure a reset?
I thought this should feature in Table 16.10.3 but I could not figure...
What is the logger message pool? There are two main definitions for it:
NRF_LOG_MSGPOOL_ELEMENT_COUNT
NRF_LOG_MSGPOOL_ELEMENT_SIZE
However it is not clear what it...
Hello ,
I want to use the NVIC to manage the interruption of the accelerometer and to run a specific program, are you ideas about the possibility of this?
Best Regard...
hi,
I am using nrf 52 DK and softdevice S132,PCA10040 board . I need to toggle a pin,set a pin,reset a pin .can anyone take this ticket to a sample code/ code snippet and...
Hi,
I have a project with 52810 which I use rc for LF clock source and I need use P00 and P01 as general GPIO, I have set both CLOCK_CONFIG_XTAL_FREQ and NRF_SDH_CLOCK_LF_SRC...
