Help Needed: BLE Not Working on nRF52810 (Tried Zephyr & nRF5 SDK)
Hi everyone, I really need help getting BLE working on my custom board with the nRF52810 . I've been trying...
Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
Greetings!
Briefly summarized: I am trying to generate SPDX files for our project, but I hit some roadblocks while running the west spdx command. I found a way to workaround...
Hello,
I'm trying to make the nrf5340-DK capable of connecting to BLE from multiple devices.
The program is based on: Bluetooth: Bluetooth: Peripheral UART .
I found...
At a connection the call function app_error_fault_handler()
with parameters
m_error_data.fault_id = 0x01 m_error_data.pc = 0x14DBE m_error_data.error_info = 0x0
Is not...
I'm trying to configure UART functionality in my program, and in the event handler under APP_UART_DATA_READY I'm missing bytes that I should normally have received. The code...
Hi,
Is possible to program the nRF52832 with a target voltage between 1.7V to 3.3V? I'm thinking to power supply the MCU with a pair of AA batteries in series.
Thanks...
I am using the "Nordic Uart Service", example to create a simple serial console which allows a user to change settings such as tx power, advertising intervals so that different...
As in the circuit diagram attached where the pin resource is insufficient For one Pin (AMULTI), I design gpio for Button and analog input as 2channel. (This switch uses the...
Hi DevZone,
I am going to apply a Arduino CAN bus shield onto nrf528400 preview DK. I was integrated this shield with Arduino board and a 3rd party BLE module. Now, I am...
I'm basing my PCB design on Nordic's reference layout. The product I'm developing will only be used for research, and is basically a one-off design. How closely do I have...
Hello,
I am using the NRF52832 for advertising every 10s.
However while entering the sleep phase, I noticed some glitches while measuring the current. You can find attached...
I am in need of some guidance around how to simulate multiple devices, with different addresses, on the same NRF52
I am currently developing a test application using the...
Hi,
(SDK 14.2 , S140 v5.0.2-alpha)
I followed the example in sdk v11 multiactivity_beacon : \examples\ble_peripheral\experimental_ble_app_multiactivity_beacon\hrs_advertiser...
I am using the nRF5_SDK_14.2.0 with two PCA10040 boards. ANT+ HR simulate from ANT+ simulator tool with ANT+ USB dongle.
Test 1 : SDK sample ble_ant_hrm_pca10040_s332...
Hello.
I have a situation that when upload the softdevice, application and bootloader for some reason stays in the bootloader after some debug I found that we enter in...
Hi,
i'am using nRF52840 (S140 v 5.0.2-alpha) DK and SDK 14.2.
i'am trying to create an application for Beacon which can advertise on 2 different MAC adresses, is it possible...
