here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
We are developing central scanning mode for our project requirement. We want to scan BLE tags which are transmitting at every 10 seconds. I have been using nRF52833...
Hello, I have a working application that transmits data to a smartphone using NUS, based off of the uart example. I would now like to integrate bonding into my application...
I have an NRF52 DK and a J-Link mini debugger. I'm trying to connect J-Link debugger to the NRF52 via the debug jumper port. I'm using a standard 10 pin SWD JTAG cable. I...
i m working with fds using segger, i'm trying to perform read and write functions and printing on putty. it showing no errors on building while debuging no output is displaying...
When create 128byte length's CHARACTERISTIC and read with NRFCONNECT on Android. NRFCONNECT returns GATT_READ_NOT_PERMIT even though sd_ble_gatts_rw_authorize_reply() completes...
Hello Team Nordic,
I have a strange problem with the UART:
I am using nRF52840 with two UARTs: UART1 for Debug-Terminal and UART0 for communication with a GPS-Module...
I have developed a code for transferring data through uart to ble. It is working properly. but when I add a line printf to my code the data transmission stops and ble will...
Hello, I am trying to use the Legacy TWI Driver in SDK 15. I have setup my my sdk_config.h file to remove all references to NRFX (New TWI Driver). Only enabling the "nrf_drv_twi...
Hi!
I have download nRF5_SDK_14.1.0, and I have IAR Embedded Workbench IDE ARM 8.20.1
I want compile ble_app_eddystone.eww from examples, but have error:
Error[Lt009...
I'm looking into the use of the nRF52840 as a light switch/dimmer for a Philips Hue system, but have been running into issues with getting connected to the Hue network. I...
I know there have been many posts on this forum regarding a similar issue, I have spent a whole day reading them and trying to get this working, to no avail.
Basically my...
After nRF52840DK is flashed with open bootloader project through J-link ( usb port J2 on the short side of the board), nRF connect is showing the following interface when...
After reviewing this thread https://devzone.nordicsemi.com/f/nordic-q-a/53743/zigbee-sdk-on-top-of-freertos I managed to get FreeRTOS working with ZigBee and BLE using the...
On the development boards, the JLink OB stops working after 24 days and needs to be disconnected to work again.
This affects at least the USB UART endpoint, but possible...
I have seen some situations where putting the modem into offline mode (CFUN=4) will cause my application to lock up because the at_cmd never returns. It looks like this is...
