void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
We propose to use the SKY66112_11_203225L, but would also prefer to use Zephyr ( Or some other RTOS, like mynewt). I am aware of how to use the softdevice, but since neither...
www.silabs.com/.../ble-mesh
Do we have similar test program as if silicon Lab?
As I am about to build some PC/Android program to demonstrate the Bluetooth Mesh Device...
I use another jlink ob board to connect to nrf52832, and when i use j-link v6.16c，it give a warning prompt "The connected j-link is defective", and i use jlink v5.12f, when...
Hi,
We have some devices in the field, and I'm occasionally seeing reboots due to NRF_FAULT_ID_SD_ASSERT. I'm logging the id and pc passed into app_error_fault_handler...
SDK13, S132
Project stopped after start. I use standart initialization:
static void peer_manager_init(void)
{
ble_gap_sec_params_t sec_param;
ret_code_t err_code;...
I've connected some sensors using I2C and SPI to a DK and their power consumption is not being reflected in the PPK. Without any BLE acitivity, the current is almost zero...
Hi,
I am using Ubuntu 16.04 (64-bits) OS.
I installed JLink_Linux_V620b_x86_64.deb and was using nRF5x-Command-Line-Tools_9_6_0_Linux-x86_64.tar
I can capture the...
Hi,
I use SES import my keil project, and my keel project work well. With SES, i meed a problem, that is , i have a global variable like this:
uint32_t g_ulMainLoopCounter...
Nordic51822 no external 32.768 k of crystals in the routine what configuration
Use this routine
nordic\nRF5_SDK_12.2.0_f012efa-3d\examples\ble_peripheral\ble_app_bps\pca10028...
When I am stepping through my application code crashing at
memset(&cccd_md, 0, sizeof(cccd_md));
"Setup information:
IDE: Using IAR
Device: nRF52832
Soft...
I'm using the NRF51822 for a project that will be powered by a lithium battery. I'm wondering if it would be safe to use a diode ( such at this one ) to drop the 4.2V LiPo...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Hello,
For BLE, there is always an ACK in link level no matter it's write/read/notify/indicate.
How about 2.4G proprietary mode? Is it possible to just send a data without...
Hello,
I am using the nrf52832 with SDK v12.3 and PCA10040. Not using any soft devices, nor the RTC. The program is intended such that timer0 is set to toggle a pin (P0_11...
