Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hello,
I have a custom nrf5340 board with an attached external RAM on the QSPI (I understand only NOR flash ICs are supported) on the older version of the SDK such as...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
I have been using the nRF54L15- PDK(0.8.1) to test various examples and projects, and everything has been working fine so far. I recently switched to the nRF54L15- DK(0.9...
Hi,
During our testing of the Zigbee NCP sample, we encountered some compatibility issues. We have flashed the NCP sample firmware onto an nRF52840 Dongle using SDK version...
Dear Nordic Technical Support,
I'm writing to report an issue I'm experiencing when trying to integrate MCUboot with a Zigbee R23 project for the nRF54L15 platform.
Issue...
Hello,
we would like to test our product after production. So I would like to connect a PC to the unit via BT-LE. My Idea was to use the nRF52840-Dongle like the nRF Connect...
Hello,
I've a battery based device that uses a buck/boost to efficiently use entire battery voltage range (4.2-3.0) . This component have a low quiescent current between...
hi support team,
I was testing 7002dk with a Asus router，i found two questions:
1.5340tfm jump to application taks about 8 seconds, why it takes so much time?
2.7002dk...
I am currently developing a firmware application on the nRF5340 where I need the device to function in dual role :
As a Bluetooth Mesh Node , communicating with other...
I’ve designed and fabricated two custom boards around the nRF52840 SoC.
I use an nRF52840 DK as an SWD debugger to communicate with each board.
Using nrfjprog...
Hi, we are planning to use npm1300 for charging a battery, but we will have a limitation on the power supply (VBUS in npm1300 naming convention): the capability of making...
LE audio can support multiple stream, but I can't find any description about following application, please advise....thanks
phone1 use unicast to play audio on headphone1...
Hi,
1.As shown in the following PSM eDRX figure, during the red period, how will the text messages sent to nRF9160 be processed? Will the nRF9160 module receive them in...
I used Nordic52480 DK(bulb) as DUT to run Matter Certification case TC-DGGEN-2.1 .
Steps:
1. setup OTBR on Pi4：./certification-tool/backend/test_collections/matter/scripts...
Hello,
I am trying to connect to the PPK2, but I see on device manager stating that the PPK2 needs drivers to be installed. I have nRF connect v5.2.0. I have tried uninstalling...
