Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Good morning,
Is it always required to use Segger J-Link in order to flash Bootloader, Softdevice and Application to a new device?
Could you summarize the different possibilities...
I have an application where I will require an external antenna as our product sits in a metal enclosure.
The example NRF91 DK development board shows a UFL connector (which...
Hi
I want to know the address of the memory used by FDS.
I set the following
I think , this setting uses 3 pages.
However, there are tags at 0x2D000 and 0x2E000...
We have a problem that we are struggling to solve. We have written an application for the Nordic Semiconductor nRF52832 which uses a proprietory radio protocol. This protocol...
Hello,
I have a question about a certain issue that came up during developing a 3 transmitter, 1 receiver setup.
So the basic setup is that the transmitters are sending...
Hi,
I am trying to compile using cmake, all the components[Softdevice, Freertos, Drivers] are built as static libraries.
Using SEGGER Embedded Studio projects compiles...
Hello I am trying to add OTA update functionality to my device which is running the nrf52810 micro with the s113 softdevice. Currently I am trying to convert the PCA10040e...
Hi!
I am working on SES studio and NRF52 DK suit.
I wanted to add ble – service files, other periphral driver and libraries files in one of the example project as per...
Hi I want to change MTU size cuz I want to send more
30bytes.
Now I'd identified only 20 bytes of data being transferred.
I changed the MTU SIZE, but it does not become...
Hi,
I set TX power for ble_app_uart application like this;
advertising
sd_ble_gap_tx_power_set(BLE_GAP_TX_POWER_ROLE_ADV, m_advertising.adv_handle , 4);
peripheral...
Dear Nordic,
just got my Thingy:91 out of the box and followed the instruction.
Very surprised that the device could not connect (blue led flashing slowly every 5sec...
Hello
I am a beginner for NRF52832 FW desgin.
Now there are some issue stuck me
The scenario could me show as below: IDE platfrom: Embedded Studio Release 4.12 SDK...
Hello we want to save power and there we had the idea to not send the scan response to the central. Because we don't need this exta 31 Byte for advertising data.
We use...
Hello,
I'm trying to write BLE app that talks to Android phone. sometimes I need to set MTU more than 23 bytes so I decided to increase NRF_SDH_BLE_GATT_MAX_MTU_SIZE....
