pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hello,
I would like to have more info about canceling the pairing request on iPhone (thru the popup that asks if you want to pair with the device which is managed by iOS...
Hello everyone, I'm severely struggling to perform a simple task. I must be missing a very simple answer and, I hope with your help that I resolve the issue.
I am trying...
I didn ' t use an external 32 . 768 crystal , the internal NRF_SDH_CLOCK_LF_SRC 0 I used。
NRF_SDH_CLOCK_LF_SRC 0
NRF_SDH_CLOCK_LF_RC_CTIV 16
NRF_SDH_CLOCK_LF_RC_TEMP_CTIV...
Hi there,
I've designed a custom board implementing the nPM1300 and am currently in the process of examining the board without any firmware. Throughout testing, I have tried...
Hello,
I am using the nPM PowerUp application with the npm1300 Evaluation kit. I am trying to configure the bucks (1 and 2) to be on/off controlled by one of the buttons...
Hi,
When I looked at the SPI lines using the oscilloscope, I saw that the MISO line had the same signal as the MOSI line. As you can see from the image, basically SPI configuration...
Hello,
I am trying to factory reset 2 nrf52840 dongles that I had very long ago with unknow applications on the dongles. When I erased and installed the image of nrf_desktop...
Hi,
I would like to know how to write to the UICR OTP (0x00FF8300) in the application core of the nRF5340 at runtime. This procedure should be performed once at the factory...
Hello
I designed a custom board and now I have to put the code in the nrf52840 module (from raytac). I have been using the nrf52840dk to write my code and now I want to...
NCS 3.0.1 MCUBOOT nRF52840
I am adding MCUBOOT to the coap_client example, which inlcudes snippets in the build configuration (ci, debug, logging, mtd). The snippets are...
I'm trying to implement DFU over USB through Serial Recovery, for a custom board using a nRF52840, following the nRF Connect SDK Intermediate Lesson 9: Exercise 4 – DFU over...
I'm trying to transmit audio data between two nRF5340DKs. These boards share timestamp information via the wireless time synchronization method here: https://github.com/nordic...
I have been using the nRF54L15- PDK(0.8.1) to test various examples and projects, and everything has been working fine so far. I recently switched to the nRF54L15- DK(0.9...
I am currently using ncs 2.9.0 on a custom board using the internal ldo and internal clock settings. It is a simple project where I take and indicate an adc and internal temperature...
It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
Hello,
I have an nRF52840 based custom board (myboard, NCS2.70)
its partitions node closely follows the nRF52840DK dts file:
both have &flash0 in the /chosen group...
I have an application that syncs via the internet using a nRF5340 and nRF7002. I am using the thingy53 with a nRF7002EB for now while the custom circuit boards are being manufactured...