Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi, I am developing sensor reading via ble using nRF52 Development Kit from scratch.
Since bluetooth, nrf, sdk stuff are a whole new world for me, I m following step by...
Hello All,
Recently I got the nRF 52840 PDK kit and wanted to start with a simple example.
I tried do the following. It works but when I use the following it doesn't....
I want to use Termite by UART. but failed. Is there any option left other than RTT ??
So how do Window user communicate with the board ?? I need to send data from mcu...
Dear Tech Support,
I'm currently working on implementing the Flash Data Storage library and ran in some problems. I'm using SDK 15.3 with softdevice s140 and a custom NRF52840...
Hi,
I'm trying to run the basic blinky exemple from 15.2 Nordic SDK on my nRF52480 hardware and get data on a puTTy window.
Unfortunately the putty window itsn't printing...
Hi, I'm trying to use two UART instances, and I have the following issues: - I'm not be able to configure both instance using NRF_SERIAL_CONFIG_DEF macro with parameter NRF_SERIAL_MODE_IRQ...
how to use the gpio pins functions in our program ? do we need a makefile and header file to read or write or use the gpio functions ?if so can you attach the makefile or...
Dear DevZone users,
Let me start this Ticket with providing the development setup I use:
OS: Windows 10 Professional
IDE: Segger Embedded Studio
Nordic board: nRF52832...
Hi
I am using nRF52DK, SDK 15.0, SD 6.0.0, multiperipheral based example with secure bootloader, FDS (7 FDS_VIRTUAL_PAGES). Uploading new software works (not tested thorougly...
I have modified a multi-central 52840 example, and would like to connect and read the characteristic value from various peripherals.
I looked through posts like the below...
Hi guys, I want to know that if I have one board that has rigado bmd 350 module that has nrf52832. But currently I donot have access to the board, so If I write firmware on...
Trying to build examples from nRF_SDK_for_Thread_and_Zigbee_v3.2.0, with SES 4.22 for PCA10056 dev kit. (Windows 10)
Of the 3 examples, 2 will not build due to linker file...
I just received the Thingy 91 this morning. I've inserted the SIM have verified it on the nRF Connect for Cloud.
I cannot proceed to the next step, as the led continues...
I already install Termite 3.4 but somehow it always not responding. Doing everything all possible thing like uninstall and restart but nothing work. Also try installing lower...
