Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
An external PA/LNA is used to extend range of nRF51822, and S110 is used for BLE, How to switch between PA and LNA? and how to disable PA/LNA when there isn't transceiving...
Hi...
Can anybody help me to run ble_peripheral example (ble_app_hrs for S130). I have build and load the code successfully but cant see the advertisement. But while debugging...
I am working with the nRF8001, and I'd like to create a services.h file that will let me broadcast battery level and as well as allow temperature to be read by a peer.
...
I ran into the issue where the clock definitions were defined in both the "board_pcaXXX.h" file and the sdk_config.h.
e.g.
NRF_SDH_CLOCK_LF_XTAL_ACCURACY
NRF_SDH_CLOCK_LF_SRC...
the signal flow is as follow:
TLV320AIC23B(as ADC)——》nRF52832（TX）——》nRF52832（Rx）——TLV320AIC23B（as DAC）
TLV320 works in master mode and nRF52832 works in slave mode. 48kHz...
Hi all,
I would like to know how to cross compile the pc-ble-driver-py for arm target.
Do you please have a prooceding tutorial for this activity?
Thanks in advance...
Hello everyone,
I have both the NRF52840 and NRF52832 dev kits. I was wondering if Nordic has released a packet sniffer to use with Bluetooth 5.0.
Is it firmware/software...
Hi,
i am using ble_app_hrs_c_pca10056_s140(nRF52840) and i want to stop execution of my program and based on button press return i want to continue my program.
i am unable...
Hi!
When I scan for BLE devices using "nrf UART 2.0" application I get a list of all available BLE devices. While running that application a bluetooth is activated on smartphone...
I'm having a few issues getting my application to run. I'm using Eclipse/gcc configured to use managed makefiles, following the tutorial here: bitknitting.wordpress.com/....
Hi
As we know, the mesh network is contained of a number of nodes, so, if we want to get the message of the nodes on the network , i think the node which is connected with...
Hi everyone,
I'm totally newbie, and was following the tutorial devzone.nordicsemi.com/.../ . (I have two board, PCA10028 with a nRF51 and PCA10040 with a nRF52)
and...
Hi,
I have a question about scan window and interval [I'm using nrf51822aa with s130 2.0.1... I performing some tests and I find a use case: If I set both of them (scan...
Hi!
I've found out that, according to this specification
www.bluetooth.com/.../16-bit-uuids-for-members
16bit uuids can be bought by companies.
But, on the other hand...
Hi,
I have an application with an accelerometer. This one communicate in I2C (TWI ). The accelerometer send a "data ready" signal every 20ms. I'm using the GPIOTE module...
Hello,
I'm running into trouble when doing a DFU of the app only using Secure Bootloader SDK13.
When it uses Bank1, it loads the whole image to the empty space after...
We recently decided to use the Nordic nRF52840 . Given the nature of the use (BLE + Thread) of this device we were asked to use Segger Embedded Studio as our development platform...
