I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I AM HAVING A COUNT VALUE WHICH IS IN THE RANGE OF 10000 - 100000 WHICH IS TO BE TRANSMITTED OVER THE BLE (OF THE BOARD) TO THE ANDROID DEVICE. I like to use nus service to...
Not really a development question. I'm looking for a wearable BLE device to use as a prototype for an academic research project (in a healthcare/hospital setting).
The...
Hi there,
Can anyone help me do secure DFU using bluetooth on PC please? I've tried every possible node.js solution to no avail.
I don't care what programming language...
Hello,
To my understanding, normally, either after a reset or powering up, the program should first run to Reset_Handler, then SystemInit, then __main.
Somehow, my program...
i used RTS service example in nRF5_SDK_13.1.0_7ca7556.
I entered the value in cccd,then i see ATT_ErrorRsp: status=0 oc=0x0012 h=17 err=5.
What's wrong with it and how...
We have tried working with nrF UART android source code from Github, it is not working, we have connectivity issue. it is working fine with the uart application which we have...
Hello, I'm developing firmware for a custom PCB with an nRF52832 chip. I've implemented almost all of the peripheral functionality I need (including TWI, GPIO, GPIOTE, delay...
Hi there,
I've already downloaded ble_mesh_v0.9.1-Alpha SDK and I can use arm-none-eabi-gcc to compile it, one thing I want to know is that how can I switch HWID to 52 in...
Hello,
I'm trying to use ble_app_hrs_rscs_relay_pca10056_s140 on a nRF52840 Preview DK using example from SDK 13.0.0_04a0bfd.
When I copy the precompiled .hex file in...
Hi,
I'm trying to add another element with a simple onoff model to control a second LED on the same server node.
I get APP_ERROR. I try declaring m_server0, m_server1, generic_get0_cb...
Hello,
I want to use at the nRF52832 a temperature sensor TMP108 and an EEPROM via TWI bus which are connected to Pin 5 (SDA) and Pin 6 (SCL). I made a lot of time until...
Hello,
I have a custom board with a Taiyo Yuden chip (it integrates an nRF51822 QFAC chip, 2 crystals and the BLE antenna).
I program it using SWD. I succesfully uploaded...
Hi,
I'm trying to use nRF52832 by external oscillator(ash7k-32.768KGZ-T).
When i use SDK13, i just add clock setting like below.
NRF_CLOCK->LFCLKSRC = (CLOCK_LFCLKSRC_SRC_Xtal...
