Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hello,
we are trying to test the mesh functionality with nrf development kit. We erased the flash on the dev kit and we programmed it with softdevice version s132v3.0.0....
As stated in the topic. We use BLE to simulate UART. As for now, we have defined our own UUIDs but there would be more straight forward to use the well defined and used one...
Hi,
I have known your board support jlink ob；I want to debug through it ;
I want to know if i need to buy the software-license from SEGGER ？
and if i need buy the software...
Now facing the problem "After disconnected, the electric current increases"...
I think softdevice is working hard even after disconnected when connecting once.
Could you...
Hi,
I'm trying to write unit tests and have arrived at the point to write tests for ble characteristic addition to a service.
To offer some background, I have written...
Hello,
I use NRF51822 and I try to output UART message onto hyperterminal program.
but every message I send it contains "APP:INFO:" in front of the message.
like...
I want to use nRF Connect v2.1.0 to debug.
But i faild to connect the correct J-link because the nRF Connect choose the wrong J-Link IDs on the COM. So i can just change...
I'd like to use nRFConnect with a direct USB/Serial connection to my nRF52832-based device. I've read that it currently checks the jLink chip.
Is there any way to configure...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
for multilink client services Nordic introduced the *_EVT_DISCOVERY_COMPLETE events and the *_c_handles_assign functions. Like the BLE_BAS_C_EVT_DISCOVERY_COMPLETE...
Hey
Would 3++ nRF51822 bluetooth smart beacon Kit sense in location application where lets say 2 beacons are quite close by (half meter) and third, the locatable beacon...
Hello,
I have modified my device name (nRF52, BLE) per the function below. When flashed to a board, I then use nRF connect to look for this device.
Using Windows nRFConnect...
I'm having an issue when trying to perform sequential reads with the ADC on 4 different pins. I've setup a timer to trigger every 1 second. In the Timer0 IRQ I setup the ADC...
Using SDK v12.2.0 . Starting a new project with Segger Embedded Studio, I have to assemble an sdk_config.h file. For example when using GPIOTE I first need to find an example...
