nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Hi
This question is related to sd_ble_gap_keypress_notify() . According to Nordic softdevice S132 v3.0.0 API:-
"This function can only be used when an authentication...
Hi
I am currently working on calculating the AoA. I have 4 nRF52833 DKs and I am using three DKs as transmitters and one as the receiver and the receiver is connected to...
This page https://www.nordicsemi.com/Software-and-Tools/Development-Kits/nRF52840-DK/GetStarted says " If step 4) below fails, you need to re-program the factory example code...
How can I calculate max and average power of this chip? During use, I intend to be at 0dB TX and 1 Mbs data rate with a 3V supply. I am going to guess the max power draw will...
Hello everyone
I am using nRF52 DK PCA10040.
I try to generate puls by Timer 0.
The puls width is 400ns.
This goal was failed.
---------------------------------...
I'm struggling to get buttonless DFU to work with FreeRTOS. I've gotten buttonless DFU sample to run on the hardware. I also have FreeRTOS running on the hardware. However...
Hello,
I need to remap ble bootloader because I want to use nrf52832_AB instead of nrf52832_AA found in dev kits.
I wish I could have this memory mapping in embedded flash...
Viewers! Don't click on a similar issue or you will lose everything you have done!
Calling this method sd_ble_gatts_characteristic_add(...) with a characteristic value...
Dear all,
Im trying to interface LIS3DH with the following code, and drivers of LIS2DH (LIS3DH and LIS2DH have the almost same hardware and config.)
I have included...
It seems there is hardware support for NB2, but the modem firmware isn't there yet.
What's the timeline on this? And if a precise time isn't available, is it in the order...
Hi!
I know, that there are some similar issues in this forum, and I checked them, but I didn't see the clue.
I try to use fstorage to write something to flash. I have...
After many hours of successful LTE connections and using the AF_LTE socket just fine (many creates, many send/receive, many closes), my application now hangs on a call to...
Hi What is the ADC frequency range and operation at nRF52833 ? we are interfacing the TUSS4470 with nRF52833 ,WITH SPI communication . is that the frequency range supports...
In past I try to solve this problem:
https://devzone.nordicsemi.com/f/nordic-q-a/51249/state-chaneged-flags
Now I have new informations about this problem.
Using hardware...
