Hello everyone,
I'm reaching out to this forum in a bit of a bind and hoping someone might be able to offer some guidance or assistance.
I'm trying to download the S340...
Hello LE-Audio team,
By any chance, do you have a working code base that supports a headset with 2 end points instead of just one as your sample nRF5340_Audio kit?
If...
Hi, I just tried to connect LSM6DSV IMU with nRF52840dk
The whole folder structure is shown below :
1. I set nrf52840dk_nrf52840.overlay file first.
2. I...
Hello,
We are designing a new Zigbee/Thread end-device sensor and I'm wondering what is the recommended part for it.
I have a demo running with nRF5340 (because the platform...
Hi Nordic team,
I'm using the nPM2100 PMIC in my design to power a microcontroller. The microcontroller sets the nPM2100 into Hibernate mode , and a vibration sensor connected...
Hello,
We are currently using the nrf52840 for development using Zephyr v3.7.99-ncs1 .
We want to use the UART in low power mode and therefore, we have used the zephyr...
My attempts to configure the Zephyr device tree to run littlefs on an external SD card have repeatedly resulted in what appears to be the creation of a small littlefs instance...
Hi.
I want to test my iBasis SIM card for NB-IoT with nRF9160DK. So, I tested with the "AT_client" example. I have followed "Getting Start with nRF8160 DK" instruction and...
Hi, I am trying to run ble example - uart in segger embedded studio. I am using 11.0 sdk. I have imported keil project into segger embedded studio. I have the error stating...
Hi devzone,
I'm using translation.
I use nRF52840. I created a firmware like the attached one based on the SDK15.3\examples\peripheral\bie_peripheral\ble_app_blinky. ...
Hi all,
I have a custom board with LED on PIN 11 of nRF52832, and I am using SWD P20 configuration to program my board through nrf52 DK PCA10040. Apparently, nRFgo Studio...
Hi
this is not a question - I'd like to give feedback about the peripheral example usbd_hid_generic.
I'm new to 52840 and new to USB. As learning lesson I tried to build...
Hi All
I am now developing BLE application on nRF52840 DK. I have a question about BLE retransmission process.
When master sends a packet to initiate a connection event...
Hello All,
When I was testing our ble keyboard, there was a problem with the Lenovo tablet connection pairing binding. Please help me, thank you!
1. Ble keyboard is based...
Hi,
I need to send data from a CSV file on the nordic board(Via fatfs library). I have presently gotten a Gatt service up and running.
I have a mobile application which...
Hello ,
Do we need to use TIMER1 ,2etc.. to use TIMER1 ? In my current configuration i have set NRFX_TIMER_ENABLED to 1 and others to 0 "NRFX_TIMER0_ENABLED and other instances...
Hello,
I'm trying to use th nRF52832 as a slave SPI device but in the examples "spis" I see the firmware uses DMA.
Can I use it without DMA?
Also, what is the difference...
Hi ,
I need to generate a count data to third party library.
So I create a timer1 ,it can work well.
But I set time_us equal to 1 ,the "timer_led_event_handler" don...
I am interfacing external RTC PCF8563 to nrf52840. Also I will be using low power sleep mode. Will it be possible to wake up nrf using 1hr alarm interrupt of rtc?
Hi ,
I am working on the project based on nrf9160.
Please verify it-
1. I want to print the current clock source of the board as board is initially work on LFCLK....
