Hi I'm testing the current consumption of the external qspi-flash on nrf5340dk [ MX25R6435F]. I have used ppk 2 to measure consumption with the dk and also have used a power...
Hi,
We are using nrf21540 in GPIO mode + mode pin ( and CONFIG_MPSL_FEM_NRF21540_RUNTIME_PA_GAIN_CONTROL) with an nrf52833.
We are developing under nrf connect sdk 3.0...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hi Nordic Teams :
I would like to check the current consumption by BLE DTM.
1. Is the table measurement is from 3.0V input?
2. I find the condition in the datasheet...
HI ALL,
nrf54l15dk,v2.8.0,peripheral_uart demo and no changes have been made.
Then add the following content to prj.conf
sysbuild.conf
mcuboot.conf
At this...
I'm developing my application with nrf 52832 and nrf SDK v17.
I know NCS is more powerful. I'm currently learning how to use it.
But now.I still need my application with...
I'm writing a wav file from the nrf52840 board to the nor flash w25q128jv with a capacity of 16mb but it seems that I can only operate on the first 2mb, even when dividing...
Hi Gene,
One of my customers using our module to pilot run.
https://static1.squarespace.com/static/561459a2e4b0b39f5cefa12e/t/5da77e178970da0cc270ef0d/1571257883383...
Hello,
I noticed that Table 7.3 of nRF52832_PS_v1.4.pdf states that 37 interrupts have been implemented, whereas the peripheral listing in the documentation as well as interrupt...
While advertising I could see some increased current peaks on one of the three channels. Its random and is observed mostly at the first or last channel of advertising.
Any...
Hi,
I wish to power optimize the proximity example application, as my intention to make a find-me tag. So I may not need the lls and tps services. Is any guidelines for...
Hi There,
I now have 4pcs PCA10056 and 4pcs PCA10059 for the development of our BT Mesh products by nrf52840 of Nirdoc. I have completed the installation of the tool chain...
Hi, I wanted to send data over Bluetooth 5.0 modules and to see on a terminal. So I used nRF52840 DK as central device ( ble_app_uart_c) and Fanstel modules ( ble_app_uart...
HELLO ALL,
I'M TRYING TO TEST THE BSC Rx EXAMPLE FROM DE SDK V16.
WHEN I DO IT USING ANTware II, EVERYTHING IS OK, SINCE IT'S ENOUGH WITH CONFIGURING CORRECTLY CHANNEL...
Hello,
This is a followup question regarding this old thread I started: https://devzone.nordicsemi.com/f/nordic-q-a/48295/hold-output-pin-during-bootloader-jump
IC: NRF52840...
Hi,
I'm relatively new to your product line, but have been spending a bit of time trying to bring the volume control functionality into a SDK16/PCA10056/s140 configuration...
Hi,
I am using SD calls to start an advertisement of BLE_GAP_ADV_TYPE_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED :
sd_ble_gap_adv_start(m_adv_handle, APP_BLE_CONN_CFG_TAG...
Hello, I have a project that's fairly mature and working great but now I want to extend the abilities of the device by using the extended PHYs. I know there are a million...
Hi
I plan to use nrf52 DK to program my device by using a connector https://www.tag-connect.com/product/tc2030-idc-nl
But should I connect it to debug in or debug out...
Hello,
background: using Keil IDE, my own board that has a nRF52840 on it. My goal is to create automatic DMA transfers from SPIM3 peripheral.
I am setting up EasyDMA...
I'm porting a working app from SDK 1.1 to 1.2, and have noted that when I make an mqtt connection close it, and re-open (to a different mqtt server) that the call to nrf_connect...
I have reviewed most (if not all) posts on this forum that relate to multiple vendor specific UUIDs but still see issues on my platform.
I am using nRF52832 (with minor...
