I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
We're looking for a low-latency 2.4GHz solution (not BLE) and the nRF51822 is oft-quoted as providing low latency, but what are the typical ms figures we could achieve...
Hello all,
in my previous question (Switch between applications (multiple services.h)) I got the advice to merge my two services into one service, including a HID over...
I am trying to create an nRF8001 based application that will broadcast battery levels (pipes broadcast, set), and give out temperature data (pipe indicate - TX_ACK) to connected...
Hi,
I'm using redbearlab's nrf51822 board. It is a arduino compatible board and hence it is using 0,1 (mapped to 9 and 11 for nrf51822). How do I make printf print to this...
Hi,
I have a Laird Development Kit for the nRF52840 (DVK-BLL654PA-R2.0) which I want to program. Unfortunately Keil uVision and nRFgo Studio have problems with programming...
Hi all,
Greeting of the day....
Here I am getting an issue with TWI interface. That I am using to communicate with sensor module with NRF52840.
The SCL------> p0...
Hi
I am currently doing a project based on the nRF52840 MCU and evaluation board
as part of my project, I have used the LPComp module, and set it up to trigger on rising...
I have updated to SDK V1.2.0 and the AWS FOTA fails to get an ip address. My version 1.1.0 AWS FOTA still works.
See settings and outcomes below
For v1.2.0
and...
Hi,
I have an application on NRF52840. I'm able to connect successfully to mobile devices, with min connection interval of 7.5 and max of 30.
However, when I try to...
Hi Nordic Devzone,
I am using the simple BLE blink peripheral example that simply advertises and blinks an LED. I am using the ble_app_blinky_pca10040_s132 example found...
The Interface MCU on my nRF52-DK (PCA10040) broke, I replaced it with the same part number (got it from the BOM) and now I am struggling to program it through the JTAG port...
How does one get Mesh Network Id and Mesh Network Name on a provisioned device?
So far I have looked through the Mesh SDK API documentation, but was unable to find an answer...
Hello all,
My project based on NRF52832 SDK13 has some bug I trying to solve. Some users of my product very rarly faces with problem of constantly rebooting NRF52. After...
Hi,
I am trying to perform ADC conversions controlled by Timer with minimal manual interaction. My goal is that every 2 seconds, the ADC takes 10 samples in quick succession...
I have a project using nrf52840. The nrf52840 communication with a nbiot mcu using uart port. In my project the nbiot download the firmware from server and send the firmware...
Hello,
I'm using 2 sparkfun nrf52840 boards. On the central board I'm using ble_app_multilink_central ( trying to integrate ble_app_uart_c example ) and on the peripheral...
it says "The SAMPLERATE timer mode cannot be combined with SCAN mode, and only one channel can be enabled in this mode." , simply why ?
When we set scan mode , and when...
Hello guys!
We want to configure ADXL362 accelerometer on Thingy:91 board to wake up nRF9160 SiP via INT1 external interrupt. For that purpose, we need to properly configure...
