Hi Nordic team,
We are planning to use the STM32H747 as the host MCU to control the nRF7002 for Wi-Fi functionality. Based on reference materials and existing use cases...
Hello Nordic team,
I am working with the nRF54H20 and would like to integrate both Enhanced ShockBurst (ESB PTX) and Bluetooth Low Energy (BLE peripheral) protocols in my...
Hello, I'm testing the nRF21540 FEM on a custom nRF52840-based board using the nRF Connect SDK.
I’ve enabled CONFIG_MPSL_FEM CONFIG_MPSL_FEM_NRF21540_GPIO_SPI CONFIG_BT_LL_SOFTDEVICE...
Hello, checking if I'm doing this right of restoring initial fw for 91X to work with Quick Start v1.2.0. as described here in Get Started, https://www.nordicsemi.com/Products...
It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
Background
For reasons that I do not want to dispute here, I am building a custom bootloader for the APP + NET cores on the nRF5340. This custom bootloader is not a Zephyr...
I am testing out the nRF54H20 on the nRF54H20-DK version 0.9.1. I have followed the steps for setup in the "Getting started with the nRF54H20 DK". I currently have nrf54h20_soc_binaries_v0...
Hi, I am using HRM example from SDK 10.0 with s130 on nrf51822 (attached project herewith). When I try to bond from Android(master control panel of Nordic), I am able to get...
100835_Rev1.PDF SRU532.pdf n5_starterkit.h
main.c
Hi,
i am currently working on the Nrf51422 chip with s310 softdevice . The problem i am facing is that when i dump...
Hi!
I'm fiddling around with the PCA10040 and the experimental_ble_app_blinky from the SDK found in examples/ble_peripheral/experimental_ble_app_blinky. I've had great...
Hello,
I'm trying to write value to a specified address with ble_flash_page_write .
I'm using ble_flash_page_write after ble disconnect event. I've tested different...
hi Ole BAUCK, my slave device is STPM33 ENERGY METER using this device we can calculate vrms,irms,real power,reactive power,energy and many more.. that device is not having...
Hi,
i'm doing my own bootloader and i want to use external flash to download image trough a spi. Now it almost works. But after an app image has been successfully transferred...
hi all,
i am using sdk v8.
i want to transmit the address through uart and read the data using UART.
i am using app_uart_get and app_uart_put api's.
PROBLEM:
if i connect...
Hi, it says that I have to put my beacon into beacon config mode in order to configure beacon device through the app. How do I enter beacon config mode in my nRF51dk? When...
Hi, In my project I need to measure current values for every sec and update those values to advertising data. So, I take manufacture field in advertising data to update the...
My set Up: Nexus 6 (Android version 6.0) as Peripheral, Nordic as Central.
I want to achieve ble pairing using 'pass key confirmation' methodology.
The nordic device has...
Hi Nordic Developers..
I am using nrf52 with softdevice 132.
In my project i am using external EEPROM(Microchip 11AA010) that uses UNI/O protocol and Single I/O Serial...
I'm using SDK 8.1.0 (SoftDevice 7). I built a version of dual_bank_ble_s110. Installed both on a freshly erased pca10028. It comes up fine and sets the LED on. It's advertising...
Hi guys,
I'm facing some trouble to put my rtc working properly. I made a code based on the rtc example but it's not incrementing the time the right way.
Bellow follows...
Hey,
I have written a custom service for my company's sensor readings on the nRF51 DK, on top of the uart peripheral example given n SDK_11.0.0. However, for the final...