I'm using Softedevice 6.0.0 and SDK 5.2. and Keil 4.7.
I Modified bootloader project so it compiles with both ble and hci transports. Currently I use button_0 and button_1...
I am working on the proj that needed 2 MCU and nrf51822 work as slave.
I would like to know any ref on how to firmware upgrade on board without external tool?
We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hi,
I have a question about DFU mesh, I'm working on light switch demo and I combined light_switch_server with DFU exam ple in order to only u pdate server node with light_switch_server...
Very newbie question, so, sorry.
I am starting to use SES and the Find and Replace works fine in the same document, but if I do it for Replace in Files (Ctrl-Alt-F), it...
Hi,
I am using SDK14.2 with softdevice v5.1.0. I have recently ported my application from SDK12.2.
When I run my application with the softdevice it works fine. But when...
Hi everyone,
I'm in trouble with the stdlib of Keil SDK , which is nRF5_SDK_15.0.0_a53641a, while compliing.
The code what I add in the demo project causes Undefined...
Hello, i'm trying to updade my firmaware using the DFU. I manage to do it with nRF Connect and nrfutil but i'm trying to a custom central to flash the software without any...
Hello,
We are testing a new device based on nRF52832. With our RF power meter the received power from the nRF52 is different if we use constant carrier or PBRS9 with 37...
Hi There,
I am trying to build an application that uses UART 0 (for debugging) and UART 1 (to read data over from a separate hardware). Simple objective is to send "Hello...
Hello,
I want to know if it is possible use nRF52 with openwave. OpenWave use FreeRTOS, lwIP and arm hardware architecture, so I suppose that it is possible but I do not...
Hi, im using nRF 52 DK. I want to interfac mpu6050 by using the example found on this page https://github.com/Martinsbl/nrf5-mpu-examples . I'm particularly using the example...
hi Support Team,
Mesh 2.0
#if GATT_PROXY if (is_provisioned) { proxy_init(); }
Where is proxy_init() declared and defined..
I am not able to goto definition by RightClick...
We need to measure a pulse width and create an event when it changes. The change will be from 10 to 80 percent, roughly - 1mS to 8mS or more. This is a very loose requirement...
Hi
I have to combine both BLE UART profile and RTC examples of nrf52 of 11.0.0 SDK for my application.When I run them individually, they are working fine.After combining...
Hello,
I am working with nRF52832 and using Keil uVISION 5.
While building the exapmple from nRF SDK v15, I am getting this error :
error: L6236E: No section matches...
Hi, I have nrf52832 and using QDEC driver. In my application I want to use values accumulated in the acc/accread register for a time of the order of seconds. Since max value...
